著作名稱：  Effect of etching parameters on gate profile by anisotropic chemical etching 
年度：  2020 
類別： 
期刊論文
Journal of the Chinese Society of Mechanical Engineers

摘要：  This pioneer study presents the phenomena of anisotropic chemical etching in the range of the
linewidth 15nm~100nm. In this study, a phasefield model is established and a resist mask is appointed on the surface to simulate a chemical etching process with a gate geometry. In the numerical simulations, the isotropic and anisotropic etching conditions are both evaluated to explore the fine chemical etching circumstances. In addition, the influences of etching parameters, such as the etching rate and the strength of the anisotropy, on the characteristics of gate profile are also demonstrated. From the simulation results, it shows that a larger loss of linewidth or a higher etch bias is involved with the increase of the etching rate. While an anisotropic etching is considered, a facetedetching profile would be generated and simultaneously the etch bias could be suppressed during the etching process. As the anisotropy is strengthened, the characteristic profile becomes more distinct with a less loss of the linewidth. These numerical simulations could provide a methodical guidance to concisely control the fine etching profile, and broaden the applications of chemical etching in the advanced robust manufacturing technologies. 
關鍵字：  
著作名稱：  Development of a wireless mesh sensing system with highsensitivity LiNbO3 vibration sensors for robotic arm monitoring 
年度：  2019 
類別： 
期刊論文
Sensors

摘要：  In recent years, multiaxis robots are indispensable in automated factories due to the rapid development of Industry 4.0. Many related processes were required to have the increasing demand for accuracy, reproducibility, and abnormal detection. The monitoring function and immediate feedback for correction is more and more important. This present study integrated a highly sensitive lithium niobate (LiNbO3) vibration sensor as a sensor node (SN) and architecture of wireless mesh network (WMN) to develop a monitoring system (MS) for the robotic arm. The advantages of the
thinfilm LiNbO3 piezoelectric sensor were lowcost, highsensitivity and good electrical compatibility. The experimental results obtained from the vibration platform show that the sensitivity achieved 50 mV/g and the reaction time within 1 ms. The results of onsite testing indicated that the SN could be configured on the relevant equipment quickly and detect the abnormal vibration in specific equipment effectively. Each SN could be used more than 10 h at the 80 Hz transmission rate under WMN architecture and the loss rate of transmission was less than 0.01% within 20 m. 
關鍵字：  multiaxis robots; LiNbO3 vibration sensor; wireless mesh network (WMN); sensor node (SN); monitoring system (MS) 
著作名稱：  The optimization of geothermal extraction based on supercritical CO2 porous heat transfer model 
年度：  2019 
類別： 
期刊論文
Renewable Energy

摘要：  This study presents a process to find the maximum heat extraction in supercritical CO2 geothermal system. Little attention in the previous studies about the thermal dispersion receives. A porous heat transfer model and the corresponding porous experimental system are proposed to build the correlation of thermal dispersion. The correlation of thermal dispersion is obtained from the fitting process between the corresponding model and experiment. The maximum geothermal extraction is found based on the optimal process and porous heat transfer model considered thermal dispersion. The optimal operated pressure and mass flow rate based on supercritical CO2 flow are obtained. These results will result in the range of the realistic operation and reduce the cost of process in insitu. 
關鍵字：  Supercritical CO2, Thermal dispersion, Porous heat transfer model 
著作名稱：  The development and optimization of an innovative piezoelectric energy harvester on the basis of vaporinduced vibrations 
年度：  2019 
類別： 
期刊論文
Mechanical Systems and Signal Processing

摘要：  Various energy harvesters were developed by several energy sources. In the heat pipe, the vapor momentum can be used to drive a mechanical structure to generate electricity. To bridge this gap, this study experimentally designed an energy harvester on the basis of a vaporinduced vibration for the innovative heat pipe application. The energy harvester, comprising a cantilever beam and polyvinylidene fluoride (PVDF), was designed using finite element method and the genetic algorithm (GA) to reach the resonance point. Copper, aluminum, and polyethylene (PE) were used as the material of the cantilever beam for the energy harvester. The optimized energy harvester was examined using a shocker, and obtained the output voltage. The output power of the harvester was affected by the vapor velocity, cantilever beam material, and natural frequency. The output voltages of the PVDF with the cantilever beam are better than the one of PVDF without the cantilever beam and it increased 367%, 393%, and 470%ascantilever beam is copper, aluminum, and polyethylene, respectively. The theoretical and practical implication, limitations of the present study for future studies are presented and studied. 
關鍵字：  Energy harvester, Heat pipe, Optimization, Genetic algorithm, Vaporinduced vibration 
著作名稱：  The design of high strength electrothermal microactuator based on the genetic algorithm 
年度：  2019 
類別： 
期刊論文
Microsystem Technologies

摘要：  Microactuator has applied on the microrobotics, microfluidics et al. widely. In general, to obtain the maximum output force is the designed requirement of electrothermal actuator. However, the displacement for the force output will result in the stress concentration. The important issue is to reduce the failure of the electrothermal actuator resulted from the stress concentration. This paper proposes an optimal process that involves using the finite element method and genetic algorithm to maximize the displacement and output force and minimize the stress concentration for enhancing the performance of an electrothermal microactuator. The results were validated by comparing the simulated results of a previous study. Geometric design parameters were used for determining the displacement, output force, and stress concentration. The optimal design was proved to increase the life expectancy of microactuator. 
關鍵字：  
著作名稱：  Stress Minimization of the Pressure Vessel by Optimal Shape Design 
年度：  2018 
類別： 
期刊論文
Journal of the Chinese Society of Mechanical Engineers

摘要：  This study proposes an optimal shape of the pressure vessel by the selfdeveloped simplified conjugated gradient method (SCGM) for minimizing the Von Mises stress of this pressure vessel. The finite element analysis built from the ANSYS parametric design language is optimized by SCGM. The results are validated by the previous study. This study proves that the optimization of geometry can reduce the stress concentration of the pressure vessel effectively.
It will benefit the design of the nuclear reactor for safe consideration. In addition, this proposed optimal method will build an effective way to simplify the engineering design procedure. 
關鍵字：  Pressure vessel, Stress concentration, Optimal method, SCGM 
著作名稱：  Study of Forcefeedback Tactile Sensor Fabricated by AlN Doped ZnO Piezoelectric Film 
年度：  2018 
類別： 
期刊論文
Journal of the Chinese Society of Mechanical Engineers

摘要：  In this study, we have developed a flexible AlN doped ZnO tactile sensor. This flexible sensor can be applied on the complex surface of the device. The tactile sensor is fabricated by AlN doped ZnO thin film deposited on the flexible polyimide (PI) substrate or copper substrate. The solgel method and spincoating method are utilized to prepare the AlN doped ZnO piezoelectric films. We have also investigated the influences of the speed of spincoating on the crystallinity and piezoelectric properties of the thin films. The methods of Xray diffraction and scanning electron microscopy are used to examine the crystallinity and the surface topography of the AlN doped ZnO thin films. In
addition, the forcefeedback analyses are performed to compare the output voltages between the sensors on the PI substrate and copper substrate. The response of force feedback proves the availability of this flexible tactile sensor and its robust piezoelectric properties. 
關鍵字：  Tactile sensor, Solgel, Thin film, ZnO, AlN 
著作名稱：  Experimental study on heat transfer of supercritical carbon dioxide in a long silica‑based porous‑media tube 
年度：  2016 
類別： 
期刊論文
Heat Mass Transfer

摘要：  The heat transfer phenomena of supercritical carbon dioxide were experimentally investigated in a vertical tube containing silicabased porous media. The experiment was conducted at various levels of static pressure, flow rates, and initial wall temperatures as well as with silica sand of porous media in a long test section to study the heat transfer characteristics of supercritical carbon dioxide (CO2). The results indicated that the average heat transfer coefficient and outlet temperature at an initial wall temperature of 150 °C were higher and lower than that of 200 °C. The heat transfer performance was significantly influenced by flow rate of supercritical CO2. The porous media was provided large heat exchange surface between particles and CO2 to increase the heat transfer coefficient, especially when small diameter of particles. When the inlet temperature was higher than the pseudocritical temperature, the heat transfer coefficient sharply dropped when x/L ≥ 0.5, because of the development of a thermal boundary and the decrease of CO2 thermophysical properties of CO2 in a far pseudocritical temperature. When the pseudocritical temperature was higher than the inlet temperature of the fluid, the local heat transfer coefficient was affected by a thermal boundary and hermophysical properties of CO2 in pseudocritical point at a higher initial wall temperature or lower supercritical ressure when x/L ≤ 0.75; only the thermophysical properties of supercritical CO2 in pseudocritical point played a pivotal role when x/L > 0.75 at a lower initial wall temperature or higher supercritical pressure. In the present study, the upercritical pressure of 10.5 MPa constituted an optimal operating condition for supercritical CO2 a long silicabased porousmedia tube because of the high heat transfer performance at 150 and 200 °C. 
關鍵字：  
著作名稱：  The Study of an Innovative Heat Removal Model of the Aluminumacetone Flat Plate Heat Pipe on High Power LEDs 
年度：  2015 
類別： 
期刊論文
Transactions of the Canadian Society for Mechanical Engineering

摘要：  It is well known that heat generation will be harmful to high power LEDs. It is hardly effectively dissipated
and results in a serious problem in the luminous efficiency. The most important issue in LED research is to
find a potential design of heat removal. The purpose of this study is to design the LEDs combined with the
cooling module of the aluminumacetone flat plate heat pipe by the experimental and numerical simulation
for obtaining high efficiency in heat removal. The high power LEDs with and without heat pipe cooling
module are compared. The numerical simulation is built and agrees with the experiment. The heat removal
efficiency of the cooling module reaches 92.09% and drops the junction temperature of LED about 36C.
This cooling module has proven to be effective in solving the heat concentration problems associated with
the LED chips. In short, the phase change cooling module will apply on the electronic component of high
heat concentration for more effective cooling method. 
關鍵字：  LEDs; aluminumacetone flat plate heat pipe; cooling module 
著作名稱：  An Experimental Study on the Compatibility of Acetone and Aluminum Flat Plate Heat Pipe 
年度：  2014 
類別： 
期刊論文
Heat and Mass Transfer

摘要：  This study investigates the compatibility of aluminum flatplate heat pipes (FPHPs) used for filling acetone as a working fluid after longterm operation of and the noncondensable gas (NCG) exhausting process. The rate of NCG generation substantially decreased after conducting the NCG exhausting process, proving the compatibility of acetone with the aluminum FPHPs. However, the thermal resistance was not enhanced because hydroxide bayerite (Al(OH)3) was generated as a product of the reaction. 
關鍵字：  
著作名稱：  Geometry Optimization of Thermoelectric Coolers Using Simplified Conjugate Gradient Method 
年度：  2013 
類別： 
期刊論文
Energy

摘要：  This paper develops an inverse problem approach to optimize the geometric structure of TECs (thermoelectric
coolers). The approach integrates a complete multiphysics TEC model and a simplified conjugategradient method. The present TEC model couples the heat and electrical conductions and accounts for all physical mechanisms occurred within TECs. Three geometric parameters, the semiconductor pair number, N, leg length of semiconductor column, Hpn, and base area ratio of semiconductor columns to TEC, g, are optimized simultaneously at fixed current and fixed temperature difference. The cooling rate on the cold end is the objective function to be maximized to obtain the optimal TEC geometry. The effects of applied current and temperature difference on the optimal geometry are discussed. The results show that at temperature difference of 20 K, the geometry optimization increases the TEC cooling rate by 1.99e10.21 times compared with the initial TEC geometry, and the optimal N decreases
from 100 to 47 with invariable g ? 0.95 and Hpn ? 0.2 mm, as the applied current varies from 1.0 A to 3.0 A. With the increase in temperature difference, the optimal N increases at smaller currents of I 1.0 A, however, it is almost invariable at larger currents of I 1.5 A. 
關鍵字：  Thermoelectric cooling, Numerical modeling, Coupling of temperature and electric potential, Simplified conjugategradient method, Optimization 
著作名稱：  Optimal Design of the Composite Laminate Hydrogen Storage Vessel 
年度：  2013 
類別： 
期刊論文
International Journal of Energy Research

摘要：  The purpose of this study is to optimize the design of a composite laminate hydrogen storage vessel for minimizing
stress concentration. The optimum design of this study uses the finiteelement method combined with a simplified
conjugated gradient method (SCGM) and genetic algorithm (GA) to find the minimization of von Mises stress of
the composite laminate hydrogen storage vessel. In this study, a composite laminate hydrogen storage vessel with
an aluminum liner and a carbon fiber/epoxy layer are considered. The winding angle and thickness of the composite
layer are proposed as optimal design variables. The comparison between SCGM and GA is discussed in order
to obtain a promising optimum in design process. Through this optimization, the best possible combination of
winding angle and thickness of composite layer has been obtained to obtain minimum possible stress concentration.
Copyright c 2012 John Wiley & Sons, Ltd. 
關鍵字：  composite laminate hydrogen storage vessel; stress concentration; optimal design; SCGM; GA 
著作名稱：  The Study of the Percutaneous Laser Disc Decompression 
年度：  2013 
類別： 
期刊論文
Advanced Science Letters

摘要：  The purpose of this study is to discuss the temperature and stress distribution problem of the interverbral disc while the surgical operation of PLDD is processing. This study also further discuss the water content of disc changes with age to cause variation of thermal conductivity thermal expansion coefficient specific heat and related parameters, and the effect of thermal conductivity related about the patients age will be illustrated. The 3D thermal structure conjugated model of the multiphysics analysis algorithm is used to understand the temperature and stress distribution of the whole domain and heat transfer phenomena under the different kinds of laser heating rate and patients. The temperature profile of the intervertebral disk is obtained and reveals the relations among the parameters. The temperature profile is predicted as the heat transfer phenomena can be handled on the surgical process. In the future, we expect that this result can be used to handle the PLDD in the presurgical simulation. 
關鍵字：  
著作名稱：  Optimization of the Shellandtube Heat Exchanger by Simplified Conjugated Gradient Method 
年度：  2012 
類別： 
期刊論文
Advanced Science Letters

摘要：  This study is to obtain the optimal design of the heat removal of the 3D shellandtube heat exchanger (STHE) by
integrating multiphysics script based on the finite element method (FEM) with the simplified conjugategradient method (SCGM). A numerical investigation of the performance of a STHE considered the tube distance and array type is conducted. The objective function is to obtain the maximum quantities of temperature difference between the inlet and outlet of the heat exchanger. After determining the optimal shape size, this study evaluates the thermal performance of the heat exchanger by varying the quantities of heat removal and efficiency. In addition, we obtain the synthesis for all the advantages of this proposed method. 
關鍵字：  Optimization Design, ShellandTube Heat Exchanger, SCGM, FEM 
著作名稱：  A Threedimensional Numerical Modeling of Thermoelectric Device with Consideration of Coupling of Temperature Field and Electric Potential Field 
年度：  2012 
類別： 
期刊論文
Energy

摘要：  Thermoelectric devices (TEs) can achieve direct conversion of heat and electricity by semiconductor materials, coupling of heat transfer and electric conduction is important to accurately predict the
performance of TEs. This paper develops a general, threedimensional numerical model of TEs with consideration of coupling of temperature field and electric potential field. The model is used to figure out the performance of thermoelectric coolers (TECs) with the temperaturedependent thermal conductivity, electric conductivity, and Seebeck coefficient of semiconductor materials. A miniature TEC is considered and Bi2(Te0.94Se0.06)3 and (Bi0.25Sb0.75)Te3 are selected as the ntype and ptype thermoelectric materials, respectively. The effect of parameters such as the temperature difference and the current is investigated under conditions of variable material properties as well as radiation and convection heat transfer occurred between the TEC and the ambient gas. The results show that the variable properties and the heat losses to the ambient gas have significant effects on the cooling capacity and the coefficient of
performance (COP) of the TEC. Threedimensional temperature distributions within the semiconductors
is observed under convective boundary condition and it becomes remarkable at large temperature differences and high currents. 
關鍵字：  Thermoelectric device, Numerical modeling, Coupling of temperature and electric potential, Variable properties, Convective boundary conditions 
著作名稱：  Effects of the Thermal Lag Ratio on the Behavior of Bioheat Transfer 
年度：  2012 
類別： 
期刊論文
Advanced Science Letters

摘要：  The dualphaselag heat transfer model is applied to investigate the behavior of heat transfer in a perfused tissue with instantaneous surface heat flux. The lag times, Tq and Tt, are the characteristic of the dualphaselag model. A modified numerical scheme is used to solve the problem for exploring the effects of Tq and Tt on the bioheat transfer. The influence of blood perfusion rate on the thermal response in tissue is investigated. The deviations with the thermal wave model of bioheat transfer and the Pennes model are presented. The results show that the dualphaselag model of bioheat transfer can be reduced to the Pennes model not only if both phase lag times of the temperature gradient Tt and the heat flux Tq are zero. The total effect of Tq and Tt on the bioheat transfer may be different for the same Tt/Tq value. 
關鍵字：  Dualphaselag model, Hybrid method, Perfused tissue 
著作名稱：  The Optimization of the Thermal Response on the ZnO Pyroelectric Film Temperature Sensor 
年度：  2012 
類別： 
期刊論文
IEEE Sensors Journal

摘要：  In a previous study, the present group designed and
fabricated ZnO thinfilm pyroelectric sensors with four different upper electrode configurations, namely rectangular, crisscross, target and web. However, the voltage response of the proposed devices was not formally analyzed. Accordingly, the present study commences by performing an experimental investigation to determine
the voltagetemperature transfer function for one of the
four electrode configurations (i.e., rectangular). An optimization algorithm based on the simplified conjugate gradient method (SCGM) and COMSOL finiteelement analysis software is then applied to establish the optimal geometry parameters of each of the four upper electrode configurations. It is shown that the optimized electrode designs improve the temperature variation rate of the four sensors by a minimum of 15%. As a result, the responsivity of the proposed devices is significantly improved. 
關鍵字：  Optimization, SCGM, thermal response, ZnO pyroelectric film sensor 
著作名稱：  Inverse Estimation of Unknown Heat Flux Boundary with Irregular Shape Fins 
年度：  2011 
類別： 
期刊論文
Int. J. Heat and Mass Transfer

摘要：  The purpose of this study is to estimate the unknown heat flux boundary conditions on the irregular shape fins for expanding the application of the inverse method. An inverse algorithm based on the sequential method and the concept of future time combined with the finite element package is used
to determine the 2D irregular shape heat conduction problems. Special features about the proposed method are that the stiffness matrix of the irregular shape can be solved from the finite element package. The estimated results are considered under the different kinds of fin types, the future time, the sensor’s location, the sensor’s number, the measured errors and the function of heat flux boundary. These estimated results are agreed with the exact solution even in the irregular shape fin. The results of this study show that this proposed method is an accurate, stable, and efficient method for solving the realistic engineering heat conduction problems. 
關鍵字：  Irregular shape fins, Inverse method, Future time, Finite element method 
著作名稱：  Optimization of Thermal Management by Integration of An SCGM, A FiniteElement Method, and An Experiment on A HighPower LED Array 
年度：  2011 
類別： 
期刊論文
IEEE Transaction on Electron Devices

摘要：  This paper proposes an original idea to minimize heat concentrations of highpower lightemitting diode (LED)
arrays. The purpose of this paper is to investigate temperature distribution with and without an optimal process of highpower LED arrays by experiment and a numerical method in order to achieve an optimal design of LED arrays for thermal management. This paper develops an effective method to design each LED position for decreasing thermal concentrations in highpower LED
arrays. In this paper, temperature profiles are measured by a thermal infrared camera and a thermocouple and compared with simulated results under different power. The optimal method is adopted by a simplified conjugate gradient method combined with a finiteelement method. This method proves reliability of simulated results in advance. Through this optimal method, efficiency of heat removal will be enforced as an extra cooling device is added. The important part is that this optimal design will not affect brightness through an illumination analysis. 
關鍵字：  Experiment, lightemitting diode (LED) array,optimization, simplified conjugated gradient method (SCGM) 
著作名稱：  The Optimization of the Heat Removal on the LED Package 
年度：  2011 
類別： 
期刊論文
Advanced Science Letters

摘要：  The aim of this article attempts to explore the optimal design of the high power LED package related the thermal
characteristics. To achieve the optimal design of the size of the slug inside the LED package is our purpose to
improve the heat removal. The simplified conjugategradient method (SCGM) is adopted to combine with the
finite element method to optimize the shape of the slug inside the LED package. The results show that the shape of the slug changing directly affects the temperature profile inside the LED. The heat generated from die
of the LED can be removed more by the change of the slug. It is obvious that the proposed method is effective on thermal optimization of the LED package. This proposed method may give rise to a new insight and more innovative possibilities in the development of the new generation LED. 
關鍵字：  Optimal Design, LED Package, SCGM 
著作名稱：  The Study of the Heat Transfer Analysis on the Platefin Heat Sinks by the Impinging Jet Flow 
年度：  2011 
類別： 
期刊論文
Progress in Computational Fluid Dynamics

摘要：  This paper aims at investigating the heat transfer phenomena of the platefin heat sinks under impinging jet cooling. The impinging jet cooling has the advantage of larger heat removal. The finite element method is used to simulate the heat transfer phenomena of the platefin
heat sinks under impinging jet cooling. The simulation results are verified by comparing with the experimental data. The parameters discussed in this study include the fin size, the Reynolds number and the impingement distance. The results of this study show that the effect of Reynolds number dominates to the heat removal. The heat removal increases with the Reynolds number obviously. In addition, the temperature profile on the fin surface is affected by the arrangement of the fin. 
關鍵字：  impingement distance; impinging jet; platefin heat sink; Reynolds number 
著作名稱：  N.S. Pai, C.C. Wang*, and David. T.W. Lin, 2010, Bifurcation analysis of a microcantilever in AFM system, J. Franklin Institute, Vol. 347, pp. 13531367. (NSC972221E269016)（SCI） 
年度：  2010 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  David T.W. Lin, C.C. Wang*, C.Y. Yang, and J.C. Li, 2010, Inverse estimation of temperature boundary conditions with irregular shape of gas tank, Int. J. Heat Mass Transfer, Vol. 53, pp. 46514662. （SCI ） ( Engineering, Mechanica) 
年度：  2010 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  C.T. Wang, K.Y. Huang, David. T.W. Lin, W.C. Liao, H.W. Lin, and Y.C. Hu, 2010, A flexible proximity sensor fabricated by fully inkjet printing, Sensors, Vol. 10, pp. 50545062.（SCI） 
年度：  2010 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  C.C. Wang, David. T.W. Lin, H.P. Hu, 2009, Error Analysis of Approximate Solutions of Nonlinear Burgers’ Equation, Applied Mathematics and Computation, Vol. 212, pp. 387395.（SCI） 
年度：  2009 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  David. T.W. Lin, W.M. Yan, H.Y. Li, 2008, Inverse problem of unsteady conjugated forced convection between parallel plates, Int. J. Heat Mass Transfer, Vol. 51, pp.9931002. (SCI) (NSC952221E269025) 
年度：  2008 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  Estimating the wall heat flux of unsteady conjugated forced convection between two corotating disks using an inverse solution scheme 
年度：  2008 
類別： 
期刊論文
ASME J. Heat Transfer

摘要：  
關鍵字：  
著作名稱：  David. T.W. Lin and C.Y. Yang, 2007, The estimation of the strength of the heat source in the heat conduction problems, Applied Mathematical Modeling, Vol. 31, pp.26962710. (SCI) 
年度：  2007 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  P. J. Cheng, David. T.W. Lin, 2007, Surface waves on viscoelastic magnetic fluid film flow down a vertical column, Int. J. Engineering Science, Vol. 45, pp.905922. （SCI）(NSC952221E269027) 
年度：  2007 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  David. T.W. Lin, 2007, A study of local effect and global effect on the micro thermal bioflows by molecular dynamics, Int. J. Biological Macromolecules, Vol. 41, pp.260265. （SCI） (NSC952221E269025) 
年度：  2007 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  C.K. Chen and David. T.W. Lin, 2005, TIP4P potential for liddriven cavity flow, ACTA Mechanica, Vol. 178, pp.223237. （SCI）(NSC922212E006002) 
年度：  2005 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  David. T.W. Lin and C.Y. Yang, 2005, The heat transfer analysis of nanoparticle heat source in Alanine tissue by molecular dynamics, Int. J. Biological Macromolecules, Vol.36, pp.225231. （SCI） 
年度：  2005 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  David. T.W. Lin and C.K. Chen, 2004, A molecular dynamics simulation of TIP4P and LennardJones water in nanochannel, ACTA Mechanica, Vol. 173, pp.181194. （SCI）(NSC922212E006002) 
年度：  2004 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  W.M. Yan and David. T.W. Lin, 2001, Natural convection heat and mass transfer in vertical annuli with film evaporation and condensation, Int. J. Heat Mass Transfer., Vol. 44, No. 6, pp.11431153. （SCI）(NSC872212E211006) 
年度：  2001 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  David. T.W. Lin and W.M. Yan, 2000, Experimental study of unsteady thermal convection in heated rotating inclined cylinders, Int. J. Heat Mass Transfer, Vol. 43, pp.33593370. （SCI）(NSC872212E211006) 
年度：  2000 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  W.M. Yan, H.Y. Li , and David. T.W. Lin, 1999, Mixed convection heat transfer in a radially rotating square duct with radiation effects, Int. J. Heat Mass Transfer, Vol. 42, pp.3547. （SCI）(NSC852212E211005) 
年度：  1999 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  The experimental study of heat extraction of supercritical CO2 in the geothermal reservoir 
年度：  2016 
類別： 
期刊論文
MATEC Web of Conference

摘要：  The heat transfer phenomena of supercritical CO2 are experimentally investigated in a horizontal tube for improving the efficiency of CO2EGS.This studydiscuss the experimental verification of the numerical simulations. The experiment is conducted for the pressure, the flow rate, and particle size 1.54mm.In addition, theexperiment and simulation that the maximum heat extractionis occurred at the 9MPa pressure and mass flow rate of 0.00109 kg/s. Themaximumspecific heat extraction at 9MPa and flow rate of 0.00082 kg/s.The results show that thenumerical model has been experimentally verified of the feasibility. Furthermore, the pseudocritical point had a significant influence on the heat extraction, temperature difference and specific heat extraction. 
關鍵字：  
著作名稱：  Heat transfer optimization of SCO2 porous flow based on Brinkman model 
年度：  2016 
類別： 
期刊論文
MATEC Web of Conference

摘要：  The purpose of this study is to obtain the optimal operating condition in order to find the maximum supercritical CO2 heat extraction in the enhanced geothermal system (EGS). In this study, the heat transfer model conjugated with the Brinkman model is used to evaluate the thermal behavior in the reservoir of the EGS. This numerical model is validated by experiment. Optimization is processed based on the NelderMead approach. The optimal operating conditions are proposed with different pressure, porosity. This study will build the optimal platform of heat source of geothermal power plant. 
關鍵字：  
著作名稱：  Heat Transfer Characteristics of Supercritical Carbon Dioxide in a Horizontal Tube 
年度：  2015 
類別： 
期刊論文
International Proceedings of Chemical, Biological and Environmental Engineering

摘要：  The convection heat transfer characteristics of supercritical CO2 in a horizontal tube were
investigated experimentally. The experimental parameters were supercritical pressures and volumetric flow
rates. The experimental results show that the heat transfer coefficient increased with flow rate. Furthermore,
the pseudocritical point had a significant influence on the heat transfer coefficient. In the study, the
supercritical pressure of 10MPaconstituted an optimal operating condition for CO2EGS because of the high
heat transfer performance at 200 ℃. 
關鍵字：  Supercritical fluid, Enhanced Geothermal System (EGS), Carbon dioxide 
著作名稱：  Fabrication of ZnO Thin Film Sensor for CO2 Monitoring 
年度：  2015 
類別： 
期刊論文
International Proceedings of Chemical, Biological and Environmental Engineering

摘要：  The flexible carbon dioxide sensor is a prospective technology for the extensive application of
oSAW device. The purpose of this study is to optimize the crystallization of ZnO film for a carbon dioxide
sensor by solgel technology and inkjet technology. The flexible CO2 sensor composes of a ZnO layer
sandwiched in between a flexible sheet, IDT electrode layer, and top sensor layer. The ZnO thin film uses the
solgel method and spin coating. Triethanolamine adds into ZnO solution to promote the robust of ZnO film.
The IDT of the top electrode layer is nano silver by inkjet printing technology. Finally, Triethanolamine film
is coated as the CO2 sensor layer. The center operating frequency of this SAW CO2 sensor is measured by the
vector network analyzer. The results prove that the significant deviation of frequency resulted from the
absorption of CO2 is observed. The characteristics of this CO2 sensor is thin, portable and flexible. The
improvement of fabricated parameters will enhance the effect of sensing of this saw CO2 sensor in future. 
關鍵字：  ZnO thin film, solgel method, CO2 sensor, inkjet printing 
著作名稱：  The Heat Extraction Investigation of Supercritical Carbon Dioxide Flow in Heated Porous Media 
年度：  2015 
類別： 
期刊論文
Energy Procedia

摘要：  The purpose of this study is to obtain the heat extraction of the supercritical CO2 in the reservoir for the EGS. The heat transfer model conjugated with the Darcy’s law employed by the finite element package is used to obtain the thermal behavior in the porous medium. The sensitivity parameter study under the various inlet velocities and porosities of the porous medium are discussed. The results show that the inlet velocity is the most important effect for the heat extraction. The temperature of exit decreases as the inlet velocity increases apparently. It means that the heat extraction will increase as the velocity decreases. However, it is evident gradually as the porosity decreases. This study can enhance the heat extraction and reduce the cost of realistic test of enhanced geothermal system. 
關鍵字：  Enhanced Geothermal Systems (EGS), Supercritical CO2 , Porous media 
著作名稱：  Experimental Study of the Heat Transfer of Supercritical Carbon Dioxide in Silicabased Porous Media 
年度：  2015 
類別： 
期刊論文
Energy Procedia

摘要：  The heat transfer phenomena of supercritical carbon dioxide are experimentally investigated in a vertical tube with silicabased porous media. The experiment is conducted for the various static pressure, the flow rate, the initial wall temperature, and nonporous or porous media. The results show that the heat transfer coefficient with porous media increases as the flow rate increases. Moreover, the excellent performance is exhibited at 10 MPa because of the effects of inlet temperature. In addition, the effects of the porosity and the initial wall temperature are weak through these results. This study will provide the effective data for regarding the operating conditions of the enhanced
geothermal system. 
關鍵字：  Geothermal, enhanced geothermal system (EGS), supercritical, carbon dioxide (CO2) 
著作名稱：  The Improvement of Parameters of Manufacturing Process on Flexible Surface Acoustic Wave Device 
年度：  2013 
類別： 
期刊論文
Applied Mechanics and Materials

摘要：  This study issues the improvement of the parameters of manufacturing on the flexible SAW device. The better piezoelectric characteristics of ZnO film will be obtained. The SolGel method is used to prepare the ZnO solution and deposits ZnO film by spin coating process. Xray diffraction (XRD) and scanning electron microscope (SEM) are used to get the crystalline property. The results reveal that ZnO film possesses better crystalline property in 400RPM of spin speed. The piezoelectric intensity of (002) direction is 1566.67 (a.u.) and atomic morphology of ZnO film are exhibited by SEM image. This better ZnO film will enhance the wave propagation of surface acoustic wave (SAW) device. It can also expand the application of SAW device. 
關鍵字：  SAW sensor, ZnO film, Piezoelectric material, SolGel method 
著作名稱：  Development of An Novel Adaptive Suspension System based on Ballscrew Mechanism 
年度：  2013 
類別： 
期刊論文
Applied Mechanics and Materials

摘要：  For the passive and semiactive suspensions are characterized as with constant parameters which cannot cope with timevariant road conditions, the suspension results are difficult to be satisfied. Although, the active ones are better than previous two on suspension performance, until now which are still far from real application for the drawbacks of complicated structure, large volume, costly, and difficult maintenance. Here, Ball Screw (BS) is with the characteristics of smaller volume, precise positioning, and well handling highspeed forward and backward transmissions. Instead of hydraulic or pneumatic mechanisms used for vehicle suspension, BS is adopted to be the main body of the proposed New Adaptive Suspension System (NASS). Besides, in order to overcome the unavoidable timedelay resulted from mechanical or computational operations, the Kalman filter, integrated with suspension controller, is used to estimate the road conditions. The effectiveness and feasibility of this proposal are confirmed through simulation studies. 
關鍵字：  Adaptive Suspension, Ball Screw, Kalman Filter (KF) 
著作名稱：  The Design of Heat Pipe Heat Exchanger CO2 EGS 
年度：  2013 
類別： 
期刊論文
Applied Mechanics and Materials

摘要：  The findings of new energy and energy harvester are the important issues for the lacking of
fossil energy. For the purpose of the effective usage of supercritical CO2 flowed from the product
well of CO2 EGS (Enhanced Geothermal System), an innovative heat pipe heat exchanger (Hx) is
designed and practiced in this study. This study presents an innovative Hx of heat pipe for extracting
the heat from CO2 or warm gas. By using the heat pipe for cooling gas is the fundamental idea of this
Hx. The experimental apparatus of Hx consists a heating blower to blow out hot gas, a circulating
cool water device, and a set of heat pipes. The efficiency of Hx is approved as the increasing air
velocity and the more fins gradually. This innovative heat pipe exchanger is proofed through our
experiment. This heat pipe Hx is suitable for the application of enhanced geothermal system (EGS)
and more energy harvesting application. 
關鍵字：  Heat pipe, Heat exchanger, Efficiency, EGS 
著作名稱：  A solution Processed ZnO Thin Film 
年度：  2012 
類別： 
期刊論文
Applied Mechanics and Materials

摘要：  The effect of ZincOxide (ZnO) thin film annealed in different ambiences is presented. To achieve low cost and environmentally friendly process, ZnO aqueous solution is synthesized by dissolving zinc acetate dihydrate in deionized water directly. Zinc oxide aqueous solution of high solubility and stability is presented. High quality and dense Zinc oxide thin film is formed by spin coating. Annealing temperatures are in the range of 300 °C~500 °C, and annealing ambiences of both air and N2 are discussed. 
關鍵字：  Thin Film Transistor, Thin Film Property, ZnO, Solution Process 
著作名稱：  David. T.W. Lin, H.T.X. Chi, C.C. Chang, C.C. Wang, and C.N.Huang, 2010, The optimal design process of the plate heat exchanger, 2010 IEEE International Symposium on Computer, Communication, Control and Automation. Tainan, Taiwan, May 57. 
年度：  2010 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  David. T.W. Lin, H.T.X. Chi, C.C. Chang, C.C. Wang, and C.N.Huang, 2010, The optimal design process of the plate heat exchanger, 2010 IEEE International Symposium on Computer, Communication, Control and Automation Proceedings, Vol. 2, pp. 237240.（SCIISTP, EI） (NSC982221E269016) 
年度：  2010 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  Hydromagnetic instability of a gravitydriven electrically conductive pseudoplastic liquid film 
年度：  2008 
類別： 
期刊論文
Journal of Aeronautics, Astronautics and AviationA

摘要：  The longwave perturbation method is employed to investigate the hydromagnetic stability of a thin electricallyconductive pseudoplastic liquid film flowing down the surface of a vertical wall in a magnetic field.
The validity of the numerical results is improved through the introduction of the flow index and the magnetic force into the governing equation. In contrast to most previous studies presented in the literature, the solution scheme employed in this study is based on a numerical approximation approach rather than an analytical method. The normal mode approach is used to analyze the stability of the film flow. The modeling results reveal that the flow stability can be enhanced by increasing the intensity of the magnetic field and the flow index, respectively. In general, the instability state can be neutralized through an appropriate control of the applied magnetic field. 
關鍵字：  Thin film, Hydromagnetic stability analysis, Pseudoplastic fluid 
著作名稱：  David. T. W. Lin, C.Y. Yang, R.Y. Wang and Y.C. Hu, 2008, An improved molecular dynamics algorithm for the larger momentum molecular system, Proc. of the 3rd Annual IEEE Int. Conference NEMS, Sanya, China, Jan. 69.（EI） (NSC952221E269025) 
年度：  2008 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  David. T.W. Lin, 2007, A molecular dynamics on the thermally developing flow of Alanine in nanochannel, Proc. of the 2nd Annual IEEE Int. Conference NEMS, pp.131135, Bangkok, Thailand, Jan. 1619.（SCI）(NSC942212E269017) 
年度：  2007 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  Y.C. Hu, C.S. Wei, C.C. Hsiao, and David. T.W. Lin, 2007, Extracting the Young’s modulus and stress gradient of thin films from the pullin voltage of a micro curled cantilever beam, Proc. of the 2nd Annual IEEE Int. Conference NEMS, pp.278281, Bangkok, Thailand, Jan. 1619.（SCI） (NSC952221E211008MY2) 
年度：  2007 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  David. T.W. Lin and Y.C. Hu, 2006, A molecular dynamics study of thermal ablation, Proc. of the 1st IEEE Int. Conference NEMS, pp.596600, Zhuhai, China, January 1821.（SCI） (NSC942212E269017) 
年度：  2006 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  Y.C. Hu, David. T.W. Lin and G.D. Lee, 2006, A closed form solution for the pullin voltage of the micro bridge with initial stress subjected to electrostatic loads, Proc. of the 1st IEEE Int. Conference NEMS, pp.759763, Zhuhai, China, January 1821.（SCI） (NSC942212E211006) 
年度：  2006 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  Development of Leadfree Forcefeedback Tactile Sensor Fabricated from BiFeO3 Piezoelectric Film 
年度：  2021 
類別： 
期刊論文
Sensors and Materials

摘要：  In this study, we develop a flexible leadfree BiFeO3 (BFO) film sensor that can be applied on
complex surfaces of devices. This sensor is fabricated by depositing BFO thin film on a
polyimide (PI)coated copper substrate. The sol–gel (SG) method and spincoating method are
utilized to prepare the BFO piezoelectric film. Two different spincoating processes under three
different sets of parameters and two different annealing temperatures are used in the fabrication.
Xray diffraction (XRD) and scanning electron microscopy are used to examine the crystallinity
and surface topography of the BFO thin films, respectively. A lifetime test is performed on the
device to validate the robustness of its piezoelectric properties, and a linear scaling relationship
between the force and output response is obtained. We propose suitable conditions for preparing
the piezoelectric film and demonstrate the reliability of this sensor. 
關鍵字：  tactile sensor, solgel, thin film, BiFeO3 
著作名稱：  A Method Integrating Optimal Algorithm and FEM on CMOS Residual Stress 
年度：  2014 
類別： 
期刊論文
J. Mechanics

摘要：  Residual stress in MEMS is of inherent importance in various respects. This study proposes a specific method using ANSYS including the birth and death method and combined with the optimal method (SCGM) to reduce the residual stresses during the CMOS fabrication process. The suitable cooling temperature for decreasing the residual stress is proposed and available. It demonstrates that the suitable parameter on the fabrication can reduce the residual stress in MEMS devices without any extra manufacturing process or external apparatus. The proposed method can expand to simulate the realistic MEMS model effectively. 
關鍵字：  Optimization, Residual stress, CMOS fabrication, SCGM 
著作名稱：  Performance Study of Heat Pipe Heat Exchanger for Ground Source Heat Pump 
年度：  2014 
類別： 
期刊論文
Journal of Chinese Society of Mechanical Engineers

摘要：  The findings of new energy and energy harvester are the important issues for the lacking of fossil energy.For the purpose of the effective usage of supercritical CO2 flowed from the product well of CO2 EGS (Enhanced Geothermal System), an innovative heat pipe heat exchanger (Hx) is designed and practiced in this study. This study presents aninnovativeHx of heat pipe for extracting the heat from CO2 or warm gas. By using the heat pipe for cooling gas is the fundamental idea of this Hx. The experimental apparatus of Hxconsists a heating blower to blow out hot gas, a circulating cool water device, and a set of heat pipes. The efficiency of Hx is approved as the increasing air velocity and the more fins gradually. This innovative heat pipe exchanger is proofed through our experiment. This heat pipe Hx is suitable for the application of enhanced geothermal system (EGS) and more energy harvesting application. 
關鍵字：  Heat pipe, Heat exchanger, Efficiency, EGS 
著作名稱：  The Optimal Design of the Thermal Spreading on the High Power LEDs 
年度：  2014 
類別： 
期刊論文
Microelectronics Journal

摘要：  New energy and energy saving are the two basic energy issues. This study proposes an innovative optimal method to design the LEDs with the high thermal spreading holder. The optimizationuses the FEM combined with the simplified conjugated gradient method (SCGM).The minimal temperature of the MCPCB backside of the LEDs is obtained throughout this design.The simulations have been proofed by the experiment of IR and thermal couple measurement. The optimal temperaturedecreases about compared with the original temperaturewithout anyactive cooling device.This design can prolong the LEDs’ life to benefit the energy saving obviously. In addition, this design combined with the active cooling device will achieve the better heat dissipation on the cooling of the electronic component. 
關鍵字：  LEDs, Thermal spreading, Optimal design 
著作名稱：  Optimal Parameter Design for Permanentmagnet Synchronous Generators Used in the Smallscale Wind Powers 
年度：  2011 
類別： 
期刊論文
Advanced Science Letters

摘要：  Due to the generators used in the smallscale wind powers must be characterized with high efficiency and low
cogging torque to meet the operation demands. However, above characteristics are conflicting. They are difficult
to approach a compromise for the optimal design. In order to serve the optimization problems with multiple
conflicting objectives, in this paper a novel method of integrating the Taguchi’s method and fuzzy inference
to optimize the parameter design is presented. The CAD simulator, RMxprt, is used to aid the design and
numerical analysis. Besides, a real permanentmagnet synchronous generator unit is implemented to confirm
the effectiveness of the proposed method. 
關鍵字：  Optimal Design, Taguchi’s Method, Fuzzy Inference, Wind Power, Cogging Torque, Permanent Magnet Synchronous Generator 
著作名稱：  Hydromagnetic Stability Analysis of a Film Coating Flow Down A Rotating Vertical Cylinder 
年度：  2011 
類別： 
期刊論文
Journal of Mechanics

摘要：  The influence of both the Rossby number and the Hartmann number on the hydromagnetic stability of a thin liquid film flowing down along the surface of a vertical ylinder is investigated. The longwave perturbation method is employed to solve for generalized nonlinear kinematic equations with a free film interface. The normal mode approach is used to compute the stability solution for the film flow. The modeling results indicate that the stability of the liquid film is enhanced by increasing the strength of the magnetic field or reducing the speed at which the cylinder rotates. By contrast, the flow becomes relatively more unstable as the cylinder radius is increased at larger values of the Rossby number. Notably, this finding is the opposite of that observed for film flows along a stationary vertical cylinder. 
關鍵字：  Hydromagnetic stability analysis, Hartmann number, Rossby number. 
著作名稱：  David. T.W. Lin*, C.N. Huang, and C.C. Chang, 2010, The optimization of the heat removal on the LED package, in press, Int. J. Advanced Science Letters. (SCIE) 
年度：  2010 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  C.N. Huang*, David. T.W. Lin, and C.C. Chang, 2010, Optimal parameter design for permanentmagnet synchronous generators used in the smallscale wind powers, in press, Int. J. Advanced Science Letters. (SCIE) 
年度：  2010 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  Optimization of the Micro Channel Heat Sink by Combing Genetic Algorithm with the Finite Element Method 
年度：  2018 
類別： 
期刊論文
Inventions

摘要：  The design of a micro multichannel heat sink to achieve the minimum thermal resistance is the purpose of this study. The numerical package is employed by using the genetic algorithm to process the heat dissipation optimization of the micro multichannel heat sink (the genetic algorithm employs the numerical package). The variables of this optimal design include channel number, channel aspect ratio and the ratio of channel width to pitch, as well as considering the weight of this micro channel heat sink in the optimal design process. Therefore, this optimization is a multiobjective
function design. The results show that the thermal resistance is decreased as 0.144 W/K, and the weight of this micro channel heat sink can be decreased, individually or simultaneously. 
關鍵字：  micro multichannel heat sink; multiobjective function; genetic algorithm 
著作名稱：  Experimental Study of Heat Transfer for Supercritical Carbon Dioxide with Upward Flow in Vertical Tube 
年度：  2014 
類別： 
期刊論文
KMUTNB: International Journal of Applied Science and Technology

摘要：  In this study heat transfer of supercritical carbon dioxide in vertical tube with 10 mm of inner diameter and
1800 mm of length was investigated experimentally. The initial temperature of tube wall was set to 150 and
200°C. The system pressures of supercritical carbon dioxide are 1100, 1500 and 2000 psi, respectively. The
experimental results show that the heat transfer coefficient and heat transfer rate increase with Reynolds number. The maximum heat transfer coefficient and heat transfer rate was occurred in 1500 psi of system pressure. The heat transfer coefficient for 150°C is higher than that of 200°C resulted from effect of specific heat. 
關鍵字：  Supercritical fluid, Enhanced Geothermal System (EGS), Carbon dioxide 
著作名稱：  The Innovated Flexible Surface Acoustic Wave Devices on Fully Inkjet Printing Technology 
年度：  2013 
類別： 
期刊論文
smart science

摘要：  An innovated fabricated process of the flexible surface acoustic wave (SAW) device is proposed in this study. Fully inkjet printing and solgel technology are used in this fabricated process. The flexible SAW device is composed of a ZnO layer sandwiched in between a flexible polyimide plastic sheet and two sets of interdigital transducers layer. The material of the top interdigital transducer layer is nano silver. The ZnO solution is prepared by solgel technology. Both the ZnO and top interdigital transducer layers are deposited by inkjet printing. The fully inkjet printing process possesses the advantages of direct patterning and lowcost. It does not require photolithography and etching processes since the pattern is directly printed on the flexible sheet. The center frequency of this prototype is matched with the design frequency. The prototype
demonstrates that the presented flexible SAW device is available for the possible application in future. It may be applied to the sensing on curve surface 
關鍵字：  Surface Acoustic Wave Device, Fully Inkjet Printing, ZnO 
著作名稱：  The Study of Molecule List Algorithm based on the Large Momentum Molecular System 
年度：  2012 
類別： 
期刊論文
Int. J. Science and Engineering

摘要：  The purpose of this paper is to propose an modified list method based on the Verlet neighbor list for the large
momentum system in the molecular dynamics field. The list
updated mechanism of this method is controlled by the
momentum of each molecule. The variation of the list is more apparent and rapid as the systems momentumincreasing through this study. Therefore, the list updated timing is realistic than the traditional Verlet neighbor list in the large momentum system, such as the nanoflow problem. It is applicable to construct the reasonable calculation and benefit to the improvement of MD’s calculation. 
關鍵字：  Molecular dynamics, Modified Verlet list, Verlet neighbor list 
著作名稱：  Optimal Design of the Composite Laminate Vessel based on SCGM 
年度：  2012 
類別： 
期刊論文
Int. J. Science and Engineering

摘要：  The purpose of this study is to optimize the design of the composite laminate vessel for minimizing the stress concentration. The optimum design of this study uses the
finite element method combined with the simplified conjugated gradient method (SCGM) to find the minimization of Von Mises stress of the vessel. In this study, the composite laminate vessel with the aluminum liner and the carbon fiber/epoxy layer are considered. The winding angle and the thickness of composite layer are proposed as the optimal design variables. Through this optimization, the best combination of the thickness and the winding angle of composite layer can be obtained to reach the minimum stress concentration. 
關鍵字：  Composite laminate vessel, Stress concentration, Optimal design, SCGM 
著作名稱：  A Molecular Dynamics Study of the Heat Transfer Phenomena in the Biotissue 
年度：  2011 
類別： 
期刊論文
Int. J. Science and Engineering

摘要：  The purpose of this study is to obtain the heat transfer phenomena of biotissue by the external heating. The molecular dynamics (MD) algorithm and the GROMACS protein data bank are used to analyze the bioheat transfer
characteristics of Alanine molecules in the microscale. The simulations focus specifically on the temperature evolution and thermal conductivity of the Alanine molecules under different kinds of thermal boundary conditions. The thermal conductivity of the Alanine molecule is calculated via the autocorrelation function of the GreenKubo formalism. Overall, the results
presented in this study provide a useful source of
reference for improving the efficacy of thermal ablation and the phenomena of the microscale hyperthermia. 
關鍵字：  Molecular dynamics, GROMACS protein data bank, Alanine, Biotissue, GreenKubo formalism 
著作名稱：  David. T. W. Lin, C.Y. Yang, R.Y. Wang and Y.C. Hu, 2008, An improved molecular dynamics algorithm for the larger momentum molecular system, IEEE Review on Adv. in Micro, Nano, and Molecular Sys., Vol.3, in Press.(NSC952221E269025) 
年度：  2008 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  David. T.W. Lin, 2007, A molecular dynamics on the thermally developing flow of Alanine in nanochannel, IEEE Review on Adv. in Micro, Nano, and Molecular Sys., Vol.2, in Press. (NSC942212E269017) 
年度：  2007 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  Y.C. Hu, C.S. Wei, C.C. Hsiao, and David. T.W. Lin, 2007, Extracting the Young’s modulus and stress gradient of thin films from the pullin voltage of a micro curled cantilever beam, IEEE Review on Adv. in Micro, Nano, and Molecular Sys., Vol.2, in Press.(NSC952221E211008MY2) 
年度：  2007 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  David. T.W. Lin and Y.C. Hu, 2006, A molecular dynamics study of thermal ablation, IEEE Review on Adv. in Micro, Nano, and Molecular Sys., Vol.1, pp.275276. (NSC942212E269017) 
年度：  2006 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  Y.C. Hu, David. T.W. Lin and G.D. Lee, 2006, A closed form solution for the pullin voltage of the micro bridge with initial stress subjected to electrostatic loads, IEEE Review on Adv. in Micro, Nano, and Molecular Sys., Vol.1, pp.349350. (NSC942212E211006) 
年度：  2006 
類別： 
期刊論文

摘要：  
關鍵字：  
著作名稱：  高功率電子散熱技術發展趨勢 
年度：  2011 
類別： 
期刊論文
先進微系統與技術構裝聯盟季刊

摘要：  電子元件的運算速度愈來愈快且體積越來越小，相對的在元件內所植入的電晶體之密度也愈來愈高，其所造成的晶片上單位面積的發熱量也愈大。因此電子冷卻成為重要的課題，其中衝擊噴流結合散熱片在電子散熱中有較高散熱效率，由於散熱片具有高熱傳導、散熱面積大、成本低等優點，再搭配衝擊噴流之強制對流所產生的高熱對流係數，可產生極佳的散熱效果。因此衝擊噴流結合散熱片的冷卻方式，具有快速、高效率和局部冷卻等優勢，更能在有限的空間內進行散熱。本文係探討高速噴流下冷卻於鰭片型散熱片的傳熱現象，利用有限元素法將模擬的結果與文獻之實驗進行比對，以驗證模擬結果之準確性，並針對衝擊噴流的雷諾數、鰭片幾何尺寸與噴嘴至鰭片距離的變化進行分析。 
關鍵字：  
著作名稱：  Fabrication of ZnO Thin Film Sensor for CO2 Monitoring 
年度：  2015 
類別： 
會議論文

摘要：  The flexible carbon dioxide sensor is a prospective technology for the extensive application of oSAW device. The purpose of this study is to optimize the crystallization of ZnO film for a carbon dioxide sensor by solgel technology and inkjet technology. The flexible CO2 sensor composes of a ZnO layer sandwiched in between a flexible sheet, IDT electrode layer, and top sensor layer. The ZnO thin film uses the solgel method and spin coating. Triethanolamine adds into ZnO solution to promote the robust of ZnO film. The IDT of the top electrode layer is nano silver by inkjet printing technology. Finally, Triethanolamine film is coated as the CO2 sensor layer. The center operating frequency of this SAW CO2 sensor is measured by the vector network analyzer. The results prove that the significant deviation of frequency resulted from the absorption of CO2 is observed. The characteristics of this CO2 sensor is thin, portable and flexible. The improvement of fabricated parameters will enhance the effect of sensing of this saw CO2 sensor in future. 
關鍵字：  ZnO thin film, solgel method, CO2 sensor, inkjet printing 
著作名稱：  Graphene Growth on Different Industrial Copper Ribbons by Chemical Vapor Deposition 
年度：  2015 
類別： 
會議論文

摘要：  In our study is investigates the graphene growth on few industrial copper ribbons. The graphene is synthesized by low pressure chemical vapor deposition. Both of the Argon and (Methane/Hydrogen) mixture are the precursors for deposition time. The surface morphology and grain growth behavior of these films are studied by SEM, AFM and OM observation. Impurities on the Cu substrate behave as the nucleation sites in the formation of carbon cluster on Cu surface. The graphene morphologies on these 4 types substrates are constituted by carbon discs in the range of 1~20 μm. Fractal geometry has been observed to study a variety of irregular films within a jigsaw of the variance grain structures. Current results verify the effect of surface impurities on the resulting graphene thin film. We suggest that a higher Cu purity substrate supports formation of larger graphene grain size. 
關鍵字：  Graphene, LPCVD, Industrial Copper 
著作名稱：  Heat Transfer Characteristics of Supercritical Carbon Dioxide in a Horizontal Tube 
年度：  2015 
類別： 
會議論文

摘要：  The convection heat transfer characteristics of supercritical CO2 in a horizontal tube were investigated experimentally. The experimental parameters were supercritical pressures and volumetric flow rates. The experimental results show that the heat transfer coefficient increased with flow rate. Furthermore, the pseudocritical point had a significant influence on the heat transfer coefficient. In the study, the supercritical pressure of 10MPaconstituted an optimal operating condition for CO2EGS because of the high heat transfer performance at 200 ℃. 
關鍵字：  Supercritical fluid, Enhanced Geothermal System (EGS), Carbon dioxide 
著作名稱：  Thermal Analysis of AluminumAcetone Flat Plate Heat Pipe Application in Heat Dissipation of High Power LEDs 
年度：  2015 
類別： 
會議論文

摘要：  The energy resources of nature are limited. According to the report from the International Energy Agency (IEA), there is 19% of the energy used for illumination. Its well known that LED is an excellent choice to instead the incandescent lamp for saving energy. But the other question comes out while the high power LED is applied. There is only about 20% of the input power converts to light energy, the rest of power is convers to heat which should be carry out from the LED chips, otherwise, the high heat concentration results in a serious problem to decrease LED working. The most important issue of the LED research is to find a potential design of heat removal and solve the problem of LED overheating. The purpose of this study is to discuss the heat removal ability of the aluminumacetone flat plate heat pipe by applying in the high power LED array. The aluminumacetone flat plate heat pipe is innovative proposed by our team. The high power LEDs with and without heat pipe cooling module is compared. The heat removal efficiency of the cooling module of the aluminumacetone flat plate heat pipe reaches 92.09% and drops the junction temperature of LED about 36 °C. The thermal resistance is discussed. The cooling module of the aluminumacetone flat plate heat pipe has proven to be effective in solving the heat concentration problems associated with the LED chips. In short, the phase change cooling module will apply on the electronic component of high heat concentration for more effective cooling method. 
關鍵字：  Aluminumacetone flat plate heat pipe; high power LEDs; thermal analysis 
著作名稱：  The Heat Extraction of SCCO2 in the Reservoir of EGS 
年度：  2015 
類別： 
會議論文

摘要：  This purpose of this study is to investigate the heat extraction of the supercritical CO2 in the geothermal reservoir for the enhanced geothermal system. The transient heat transfer model conjugated with the model of Brinkman equation employed by the finite element package is used. The sensitivity parameter study under the various applied heat flux, porosity and pressure are done. The dynamic and thermal phenomena in the porous medium are obtained. The effects of lower pressure and higher applied heat flux will increases the heat extraction effectively. It represents that the better heat extraction will be obtained if we can combine the suitable operating conditions. Therefore, it exists an optimal condition in the applied heat flux and pressure. In addition, we observe clearly that the heat extraction decreases as the porosity increases slightly. It still illustrates that the porosity will affect the heat extraction even it is minor. This study can enhance the heat extraction and reduce the cost of realistic test of enhanced geothermal system. 
關鍵字：  Supercritical CO2, EGS, Heat Extraction 
著作名稱：  The Magnetohydrodynamic Field on the Surface Instability of Axisymmetric Condensate Films at Liquid–vapor Interfaces 
年度：  2015 
類別： 
會議論文

摘要：  It is highly desirable to high performance for homogeneous film growth can be developed in
various industrial applications. Magnetohydrodynamics (MHD) is the study of the interaction of electrically
conducting fluids and electromagnetic forces. In magnetohydrodynamic flows, the conducting magnetic field
and the fluid strongly interact and create complex magnetic and dynamic phenomena. In practice, the optimum
conditions can be found through the use of a system to alter stability of the film flow by an appropriate
control of the applied magnetic field. Flow governing equation on thin film flow is solved on an orderbyorder
basis by the perturbation method. Multiple scale method is used to derive the Ginzburg Landau equation, and a
filtered wave with no spatial modulation is considered to analyze the flow criteria and classify the regions where
the threshold amplitude exists. The modeling results indicate the degree of stability is increased in the film system with condensate effect. Furthermore, it is shown that by increasing the magnetic field and cylinder radius
tends to enhance the stability as traveling down along the vertical cylinder. 
關鍵字：  
著作名稱：  Effects of Copper Substrate Compounds on Graphene Growth 
年度：  2014 
類別： 
會議論文

摘要：  In this research, we investigate the graphene growth on four types of copper ribbon. The graphene thin film synthesized by low pressure chemical vapor deposition (LPCVD)method. Both of the Argon and (CH4/H2) mixture are the precursors for different deposition time in a range 5~30min. The surface morphology and grain growth behavior of these films were studied by optical microscopy associated with bright and dark filed observation. Impurities on the Cu substrate behaved as the nucleation sites in the formation of carbon cluster on Cu surface. The morphology for these for types substrates is constituted by carbon disc in the range of 1~100 micrometer. Fractal geometry has been observed to study a variety of irregular films within a jigsaw of the variance grain structures. Based on these results, we suggest that the growth of graphene thin films can be described by the fractal dynamics. The distribution of the surface impurities enhances grain structure homogeneous of the graphene film. 
關鍵字：  graphene, LPCVD, fractal dynamics 
著作名稱：  Experiment of the Porous Heat Extraction of Supercritical CO2 
年度：  2014 
類別： 
會議論文

摘要：  The heat transfer phenomena of supercritical carbon dioxide are experimentally investigated in a vertical tube for improving the efficiency of CO2EGS. The experiment is conducted for the various flow rate and the initial wall temperature. The results show that the heat transfer coefficient with porous media increases as the flow rate increases. Moreover, the excellent performance is exhibited at 1500 psi because of the effects of inlet temperature. In addition, the effects of the porosity and the initial wall temperature are weak through these results. This study will provide the effective data for regarding the operating conditions of the enhanced geothermal system. 
關鍵字：  Geothermal, enhanced geothermal system (EGS), supercritical, carbon dioxide (CO2) 
著作名稱：  Investigation of Heat Extraction from Heated Porous Media in Supercritical CO2EGS 
年度：  2014 
類別： 
會議論文

摘要：  The purpose of this study is to obtain the heat extraction of the supercritical CO2 in the reservoir for the enhanced geothermal system (EGS). The heat transfer model conjugated with the Darcy’s law employed by the finite element package is used to evaluate the thermal behavior in the porous medium. The influence of heat extraction on different inlet velocity and various porous porosity is studied. The simulation results show that the inlet velocity is the major parameter for the heat extraction. The temperature of exit decreases as the inlet velocity increases apparently. It means that the heat extraction will increase as the velocity decreases. However, the effect of porous porosity should also be considered since the heat transfer area will be influenced by different porosity. The effects of larger heat transfer area and slower flow will increases the heat extraction effectively. 
關鍵字：  heat extraction; geothermal; supercritical; porosity 
著作名稱：  Investigation of Thermal Phenomena in the Reservoir of Supercritical CO2EGS base on Brinkman Model 
年度：  2014 
類別： 
會議論文

摘要：  The purpose of this study is to obtain the heat extraction of the supercritical CO2 in the reservoir for the enhanced geothermal system (EGS). The heat transfer model conjugated with the Brinkman’s law employed by the finite element package is used to obtain the thermal behavior in the porous medium. The different pressure of the reservoir, the various inlet volumetric flow rate are discussed. The simulation results show that the temperature difference between the wall and working fluid at the outlet is strongly influenced by the inlet volumetric flow rate, which is, the heat extraction will increase as the volumetric flow rate decreases. However, the maximum heat extraction can be obtained under the appropriate reservoir pressure due to the particular property of supercritical CO2. 
關鍵字：  Enhanced Geothermal System (EGS) , Supercritical CO2 , Porous media 
著作名稱：  Parametric Analysis of Electromagnetic Waves Shielding of Metamaterial Structures 
年度：  2014 
類別： 
會議論文

摘要：  “Metamaterial” is a unique material which has negative permittivity and negative magnetic permeability as well [13], and by embedding microscalemetallic structures in dielectric materials, it features shielding effect. In this study, a threedimensional numerical model of the electromagnetic wave shielding effect of a metamaterial structure is developed based on framework of a commercial computer package. The metamaterial layer includes a layer of periodic metallic pattern and a layer of dielectric material. It is used as a frequency selective surface which can achieve nearly perfect shield in terahertz regime. In addition, effects of geometric parameters with the structure of the metamaterial layers on shielding of incident electromagnetic wave are predicted for different patterns and geometries. In the analysis, results show if cell size, pattern size or gap size of the pattern is increased, the frequency selective range of shielding is increased. The predicted frequency selective range is found to be independent of the solution domain. For a silver pattern of 0.5mm width, the shielding ratio of typical peak attenuation is 34% at 4.2 GHz. 
關鍵字：  metamaterial; parametric analysis; numerical simulation; electromagnetic wave 
著作名稱：  The Design of Flexible CO2 Sensor based on the SAW Device 
年度：  2014 
類別： 
會議論文

摘要：  BSTRACT
This study designs and fabricates an innovative flexible CO2 sensor based on the SAW device. The flexible sensor is composed of a ZnO layer sandwiched in between a flexible sheet, IDT electrode layer, and top sensor layer [1]. The solgel method and spin coating are used on the ZnO thin film. In advance, addition of Triethanolamine promotes the robust of ZnO film. The IDT of the top electrode layer is nano silver by inkjet printing technology [2]. Inkjet printing process possesses the advantages of direct patterning and lowcost. It does not require MEMS processes since the pattern is directly printed on the flexible PI sheet [3]. Finally, Triethanolamine film is done by spin coating as the sensor layer. The center operating frequency of this SAW CO2 sensor is measured by the vector network analyzer. The results prove that the significant deviation of frequency resulted from the absorption of CO2 is observed. The characteristics of this CO2 sensor is thin, portable and flexible. The improvement of fabricated parameters will enhance the effect of sensing of this saw CO2 sensor in future.

關鍵字：  CO2 sensor、ZnO film、Solgel method 
著作名稱：  The Study of the Cooling Module based on the AluminumAcetone Flat Plate Heat Pipe of High Power LED 
年度：  2014 
類別： 
會議論文

摘要：  The power of LED increases very fast and the application of LED is more widely as the technology growing. The advantages of LED are small size, long lifetime, fast response, high lighting efficiency, antiimpact and colorful. The most important issue of the LED research still is to find a potential design of heat removal and solve the problem of LED overheating. The purpose of this study is to design the LEDs combined with the cooling module of the aluminumacetone flat plate heat pipe by the experiment and numerical simulation for the high efficiency of heat removal. The optimization of LED package is done by our team [1] for the optimal heat removal of LED chip. In 2011, the optimal arrangement of LED array is proposed for avoiding the high concentration of the power density [2]. The innovative aluminumacetone flat plate heat pipe is proposed and fabricated by our team [3]. The heat pipe which transfer the heat by phase transition is suit for the working temperature of LED. The efficiency of this cooling module is discussed by the experiment and simulation for the realistic application. This cooling module can be used for heat removing of the high power electronic unit. Also, it can be used for the energysaving engineering. 
關鍵字：  heat transfer; high power LED ; aluminumacetone heat pipe 
著作名稱：  Wave Evolution On Roll Coating Flows Of Thin Macromolecular Liquid Films 
年度：  2014 
類別： 
會議論文

摘要：  Lubricating processes, surface roll and spin coatings of a moving rotation substrate by a liquid layer are of
importance in a variety of industrial application. In practice, coating liquids often contain NonNewtonian
pseudoplastic macromolecular liquids. This is somewhat complicated than that of the Newtonian flow. In industry
applications, the quality of the final product is largely dependent on the hydrodynamic stability of the liquid film as it flows over the substrate. Flow governing equation on roll coating is solved on an orderbyorder basis by the longwave perturbation method. Normal mode method is used to analyze the flow regime and categorize the regions where the threshold amplitude exists in the linear stability. The viscosity of the macromolecular fluid appears to be lower in the higher shear rate part of the experiment. When coating a moving substrate with a thin liquid film, even macroscopic instabilities of the film system can result in a nonhomogenous film growth. The result shows the Newtonian fluid tends to stabilize the thinfilm system than that of pseudoplastic macromolecular fluid. 
關鍵字：  macromolecular liquid; Norrmal mode method; roll coating 
著作名稱：  The Thermal Phenomena of the Supercritical CO2 in the Reservoir of the Enhanced Geothermal System based on Brinkman Model 
年度：  2014 
類別： 
會議論文

摘要：  The paper is to discuss the thermal phenomena of the supercritical CO2 in the geothermal reservoir for the enhanced geothermal system. The transient heat transfer model conjugated with the Brinkman model of employed by the finite element package is used to obtain the dynamic and thermal behavior in the porous medium. The different pressure of the reservoir, the various inlet volumetric flow rate are discussed. The results show that the inlet volumetric flow rate results in the temperature difference between the wall and working fluid on the exit apparently. It can be predicted that the heat extraction will increase as the volumetric flow rate decreases. In addition, the suitable operated pressure will reach the maximum heat extraction for the reason of property of supercritical CO2. 
關鍵字：  
著作名稱：  Design of the Cooling Module of LEDs based on the AluminumAcetone Flat Plate Heat Pipe 
年度：  2014 
類別： 
會議論文

摘要：  The waste heat generated by high power LEDs is hardly effectively dissipated, therefore, it results in a serious problem in the luminous efficiency. The most important issue of the LED research is to find a potential design of heat removal and solve the problem of LED overheating. The purpose of this study is to design the LEDs combined with the cooling module of the aluminumacetone flat plate heat pipe by the experiment for the high efficiency of heat removal. The aluminumacetone flat plate heat pipe is innovative proposed by our team. The high power LEDs with and without heat pipe cooling module is compared. The heat removal efficiency of the cooling module of the aluminumacetone flat plate heat pipe reaches 77% and drops the junction temperature of LED about 36 °C. The cooling module of the aluminumacetone flat plate heat pipe has proven to be effective in solving the heat concentration problems associated with the LED chips. In short, the phase change cooling module will apply on the electronic component of high heat concentration for more effective cooling method. 
關鍵字：  LEDs, heat removal, aluminumacetone flat plate heat pipe, cooling module. 
著作名稱：  Impurity Influence of Graphene Growth on Cu Ribbon 
年度：  2014 
類別： 
會議論文

摘要：  For electronic applications, synthesis of large area, single layer grapheme with high crystallinity is required. One of the most promising and widely applied methods is chemical vapor deposition (CVD) using Cu thin film as catalysis. Howerer, the CVD grapheme is generally polycrystalline and contains a great many grain boundaries and defects. The microstructure defects occurr when the catalysis surface contains the impurities’. Grain boundary and defect limit intrinsic physical properties of graphene. In this perspective, we discuss the growth mechanism of grapheme on a Cu foil associate with different Cu purities in a range 90% to 98%. We give a comparison of the Cu catalysis film impurity effect by the observation of the domain structure of graphene. Finally, we emphasize the importance of the growth condition and impurity of the Cu catalysis for the realization of single crystalline graphene. 
關鍵字：  
著作名稱：  The Heat Extraction Investigation of Supercritical Carbon Dioxide Flow in Heated Porous Media 
年度：  2014 
類別： 
會議論文

摘要：  The purpose of this study is to obtain the heat extraction of the supercritical CO2 in the reservoir for the EGS. The heat transfer model conjugated with the Darcy’s law employed by the finite element package is used to obtain the thermal behavior in the porous medium. The sensitivity parameter study under the various inlet velocities and porosities of the porous medium are discussed. The results show that the inlet velocity is the most important effect for the heat extraction. The temperature of exit decreases as the inlet velocity increases apparently. It means that the heat extraction will increase as the velocity decreases. However, it is evident gradually as the porosity decreases. This study can enhance the heat extraction and reduce the cost of realistic test of enhanced geothermal system. 
關鍵字：  
著作名稱：  Experimental Study of the Heat Transfer of Supercritical Carbon Dioxide in Silicabased Porous Media 
年度：  2014 
類別： 
會議論文

摘要：  The heat transfer phenomena of supercritical carbon dioxide are experimentally investigated in a vertical tube with silicabased porous media. The experiment is conducted for the various static pressure, the flow rate, the initial wall temperature, and nonporous or porous media. The results show that the heat transfer coefficient with porous media increases as the flow rate increases. Moreover, the excellent performance is exhibited at 10 MPa because of the effects of inlet temperature. In addition, the effects of the porosity and the initial wall temperature are weak through these results. This study will provide the effective data for regarding the operating conditions of the enhanced geothermal system. 
關鍵字：  
著作名稱：  Experimental Study of Heat Transfer of Supercritical Carbon Dioxide 
年度：  2014 
類別： 
會議論文

摘要：  In this study heat transfer of supercritical carbon dioxide in vertical tube with 10 mm of inner diameter and
1800mm of length was investigated experimentally. The initial temperature of tube wall was set to 150 and 200℃. The system pressures of supercritical carbon dioxide are 1100, 1500 and 2000 psi, respectively. The experimental results show that the heat transfer coefficient and heat transfer rate increase with Reynolds number. The maximum heat transfer coefficient and heat transfer rate was occurred in 1500 psi of system pressure. The heat transfer coefficient for 150℃ is higher than that of 200℃ resulted from effect of specific heat. 
關鍵字：  Supercritical fluid, Enhanced Geothermal System (EGS), Carbon dioxide 
著作名稱：  The Parametric Design of the Fabrication on the Flexible Surface Acoustic Wave Device 
年度：  2014 
類別： 
會議論文

摘要：  The flexible surface acoustic wave (SAW) device is a promising product for the expanded application of SAW
device. The purpose of this study is to obtain the better output gain of the flexible SAW device. The parametric
modification on the fabrication of the flexible surface acoustic wave devices is processed. The ZnO solution is prepared by sol?gel technology. We design inter digital transducer (IDT) pattern and deposit ZnO solution on the flexible polyimide plastic (PI) substrate by inkjet printing process. Next, the frequency of SAW device is measured by the vector network analyzer. The effect of the thickness of ZnO film and IDT will be studied in this paper. The piezoelectricity of the film increases as the thickness of the film increases. The output gain is better as the thickness of the IDT is 500μm. This study can improve the efficiency of the SAW device and expand the application of the SAW in future. 
關鍵字：  SAW, ZnO, Sol?Gel method, Inkjet printing 
著作名稱：  The Electromechanical Behavior of a MicroBeam Driven by Traveling Electrostatic Force 
年度：  2014 
類別： 
會議論文

摘要：  There is no literature mentioning the electromechanical behavior of a microbeam, one of the common microstructure in micro devices, driven by traveling electrostatic forces. This paper is to present the dynamics and stabilities of a microbeam on which an electrostatic force travels to and fro. The traveling electrostatic force may be induced by a row of actuated electrodes which are arranged beneath the microbeam and actuated sequentially. The linearized distributed model considering the electromechanical coupling effect between electrostatic force and structure is derived based on the small deflection assumption. According to the analytical results, the microbeam will resonate when the traveling speeds of the electrostatic force approach some critical speeds. The critical speeds are equal to the ratio of the natural frequencies to the wave number of the correlative natural mode of the microbeam. Besides, the microbeam may be unstable at some traveling speeds differing from the critical speeds. Furthermore the unstable regions expand with increasing driving voltage. This article may lead to a new research branch on electrostaticdriven micro devices. 
關鍵字：  electrostatics, MEMS, microstructures, stabilities 
著作名稱：  The Design of Heat Pipe Heat Exchanger for CO2 EGS 
年度：  2013 
類別： 
會議論文

摘要：  The findings of new energy and energy harvester are the important issues for the lacking of fossil energy. For the purpose of the effective usage of supercritical CO2 flowed from the product well of CO2 EGS (Enhanced Geothermal System), an innovative heat pipe heat exchanger (Hx) is designed and practiced in this study. This study presents an innovative Hx of heat pipe for
extracting the heat from CO2 or warm gas. By using the heat pipe for cooling gas is the fundamental idea of this Hx. The experimental apparatus of Hx consists a heating blower to blow out hot gas, a circulating cool water device, and a set of heat pipes. The efficiency of Hx is approved as the increasing air velocity and the more fins gradually. This innovative heat pipe exchanger is proofed through our experiment. This heat pipe Hx is suitable for the application of enhanced geothermal system (EGS) and more energy harvesting application. 
關鍵字：  Heat pipe, Heat exchanger, Efficiency, EGS 
著作名稱：  The Study of the Performance of the Acetone and Aluminum Flat Plate Heat Pipe 
年度：  2013 
類別： 
會議論文

摘要：  The flat plate heat pipe (FPHP) made of aluminum with a coppercoated surface, for filling acetone, is investigated by experiment. Performance indicators, such as temperature uniformity, thermal resistance and maximum heat transport are measured on the varying filling amounts of working fluid. After 2000 h of compatibility test, the results show that the generated rate of noncondensable gas (NCG) for a 1.4 g filling amount is larger than the one of 1.7 g. After that, The NCG exhausted process is operated after this 2000 h, then continued for an additional 2000 h compatibility test. Finally, it can proof that the FPHP is available under the compatibility between the aluminum and acetone. 
關鍵字：  Flat Plate Heat pipe, Aluminum, Noncondensable gas 
著作名稱：  Development of An Novel Adaptive Suspension System based on Ballscrew Mechanism 
年度：  2013 
類別： 
會議論文

摘要：  For the passive and semiactive suspensions are characterized as with constant parameters which cannot cope with timevariant road conditions, the suspension results are difficult to be satisfied. Although, the active ones are better than previous two on suspension performance, until now which are still far from real application for the drawbacks of complicated structure, large volume, costly, and difficult maintenance. Here, Ball Screw (BS) is with the characteristics of smaller volume, precise positioning, and well handling highspeed forward and backward transmissions. Instead of
hydraulic or pneumatic mechanisms used for vehicle suspension, BS is adopted to be the main body of the proposed New Adaptive Suspension System (NASS). Besides, in order to overcome the unavoidable timedelay resulted from mechanical or computational operations, the Kalman filter, integrated with suspension controller, is used to estimate the road conditions. The effectiveness and feasibility of this proposal are confirmed through simulation studies. 
關鍵字：  Adaptive Suspension, Ball Screw, Kalman Filter. 
著作名稱：  The Improvement of Parameters of Manufacturing Process on Flexible Surface Acoustic Wave Device 
年度：  2013 
類別： 
會議論文

摘要：  This study issues the improvement of the parameters of manufacturing on the flexible SAW device. The better piezoelectric characteristics of ZnO film will be obtained. The SolGel method is used to prepare the ZnO solution and deposits ZnO film by spin coating process. Xray diffraction (XRD) and scanning electron microscope (SEM) are used to get the crystalline property. The results reveal that ZnO film possesses better crystalline property in 400RPM of spin speed. The piezoelectric intensity of (002) direction is 1566.67 (a.u.) and atomic morphology of ZnO film are exhibited by SEM image. This better ZnO film will enhance the wave propagation of surface acoustic wave (SAW) device. It can also expand the application of SAW device. 
關鍵字：  SAW sensor, ZnO film, Piezoelectric material, SolGel method 
著作名稱：  The Study of the Enhancement of MicroVibrationInduced Harvester based on Vapor Impacting 
年度：  2013 
類別： 
會議論文

摘要：  With technology rapidly advance, the energy of demand is also with the greatly increased. Therefore, the development of new energy or energy harvesting attracts much attention. Our group has proposed an innovated micro heat pipe harvester based on the micropiezoelectric vibrationinduced power device. The deformation of the piezoelectric material by vapors impacting enables it to convert the vapor momentum to the power. In this paper, the purpose is to enhance the output of the micro heat
pipe generator by the optimization of the vibrationinduced device. A suitable cantilever beam combined with piezoelectric material is designed by multiphysics and genetic algorithm. The optimal geometry is found to approach its natural frequency. The experimental results show that the power improves about 293.38%. Through this study, the micro heat pipe generator will be practiced
and approach the available usage. 
關鍵字：  energy harvester; cantilever beam; resonance; natural frequency 
著作名稱：  Optimization of the Micro Channel Ladder Shape Heat Sink 
年度：  2013 
類別： 
會議論文

摘要：  The channel heat sink is in contact with the working fluid to remove the heat. But much channel will result
higher pressure difference issue in the micro multichannel heat sink. In this paper, a ladder shape channel (link between the parallel channel) is proposed to correct the problem of high pressure difference. The design of the link decreases the pressure difference for reducing the pump work of the micro multichannel heat sink. The purpose of this paper is to maximize the efficiency of the micro multichannel ladder shape heat sink by using optimization design. An optimization method based on the genetic algorithm and COMSOL 3D conjugated thermalfluid model is applied to establish the optimal geometry parameters of the link. The results show that this optimized heat sink design can improve the efficiency more than 43%. And the heat removal of the proposed device is significantly improved. 
關鍵字：  micro channel heat sink; ladder shape; optimization; genetic algorithm 
著作名稱：  The Design and Fabrication of the Vibrationinduced Energy Harvester on the Heat Pipe Generator 
年度：  2012 
類別： 
會議論文

摘要：  The most important issue is to find the potential energy inside the heat pipe. The focus of this paper is on the investigation of using a vapor mode piezoelectric film for energy harvesting from a fluid flow. Design of the energy harvester with an assembly technique is described. The experimental setup is used to measure vapor velocity, and voltage output of the device. The fabricated device is tested under the different. It shows that a very small continuous power and can fit with the requirements of piezoelectric materials MEMSscale sources. This design can improve the previous concepts of the heat pipe generator. 
關鍵字：  
著作名稱：  The Fabrication of Flexible Surface Acoustic Wave Devices on Fully Ink Jet Technology 
年度：  2012 
類別： 
會議論文

摘要：  The flexible surface acoustic wave (SAW) device is a promising product for the expanded application of SAW device. Over the past few years, a very few attempts have been made it on the flexible substrate. The purpose of this study is to propose an innovated process for abricating the flexible SAW devices by solgel technology and fully ink jet technology. The ZnO solution is repared by solgel technology and deposits on the flexible olyimide plastic (PI) substrate by fully ink jet process. Next, the high gain amplifier and an
impedance match circuit are consisted be a surface acoustic wave device. Through the comparison between the predicted value and experimental center frequency, the experimental center frequencies agree with the predicted value and operate. Finally, the analysis of surface acoustic wave propagation characteristics is used the Finite Element Method (FEM).The numerical model will be built for optimization in future. 
關鍵字：  
著作名稱：  An Experimental Study for Compatibility of the AluminumAcetone Flat Plate Heat Pipe 
年度：  2012 
類別： 
會議論文

摘要：  The advantage of aluminum heat pipe is cost and weight. The ammonia is typically used as working fluid in aluminum heat pipe. Because of the toxicity of ammonia, the ammoniaaluminum heat pipe is not used in general user. The acetone is considerable due to low toxicity. However, little literature has been published on the aluminumacetone heat pipe reliability. In this study, the aluminumacetone flat plate heat pipe is examined at high temperature and long time to accelerate generation of noncondensable gases (NCGs).The objective of this study is to examine reliability of aluminumacetone flat plate heat pipe and use the process to exhaust NCGs for wateraluminum produce. It will benefit to improve performance of aluminumacetone heat pipe. 
關鍵字：  
著作名稱：  Bifurcation Analysis of Trailing Edge Angle for Aeroelastic System 
年度：  2012 
類別： 
會議論文

摘要：  An aeroelastic system combines several complex theories of physics. These principles will cause instability situations or be interacted each other. If this behavior occurs, it will result in the fatigue problems or structural damages on the wings of aircrafts. In order to
avoid these conditions to occur, this paper studies the
nonlinear dynamic behaviors of aeroelastic system under
specific operating conditions and employs differential
transformation method (DTM) to decrease the calculation errors. Also, the bifurcation diagram, Poincare map, and power spectra are used to analyze the numerical results. The results reveal a complex dynamic behavior comprising periodic, subharmonic, and nonperiodic responses of the system. Especially, the nonperiodic motion occurs at the interval of ±180o for angle of trailing edge. The proposed method provides an effective means of gaining insights into the nonlinear dynamics of aeroelastic systems. 
關鍵字：  Aeroelastic, Differential transformation method, Bifurcation diagram 
著作名稱：  Optimal Design of the Electrothermal VBeam Microactuator Based on GA for Stress Concentration Analysis 
年度：  2011 
類別： 
會議論文

摘要：  The stress concentration of the electrothemal microactuator is an important issue in the MEMS structure
resulting from the existence of stress concentration essentially to change the performance and reduce the structural life time of MEMS devices. This paper proposes a method to optimize the fillet radius of the electrothermal Vbeam microactuators due to bent beam connected with electrical pad. The genetic algorithm combines with the finite element method to design the
optimal fillet radius of bent beam. A novel design of the fillet radius on Vbeam actuator can significantly improve the stress concentration. In this study, we use the proposed method to design the beam width and thickness to obtain the relative minimum stress, firstly. Then, the optimal fillet radius can achieve by using the same method at the given beam width and thickness. The results show that the stress concentration can be reduced about 57.7% after optimization. 
關鍵字：  Fillet radius, stress concentration, genetic algorithm 
著作名稱：  The Heat Transfer Analysis of the Hyperbaric Oxygen Chamber with Cooling System 
年度：  2011 
類別： 
會議論文

摘要：  The overheated problem is the important issue in the operation of the hyperbaric oxygen chamber. A cooling system is applied to reduce the temperature of the hyperbaric oxygen chamber. We present the finite element method to build three types cooling system for solving the overheated phenomena in this problem. For achieving the better cooling way, this investigation considers different types of cooling channel and pressure of the chamber in this simulated process. These simulated results show that the proposed method is accurate, stable, and efficient for handling the heat transfer problems. We expect that the proposed study can apply to ameliorate the overheated problem effectively. 
關鍵字：  Hyperbaric Oxygen Chamber, Overheat problem, Cooling System 
著作名稱：  Using Genetic Algorithm to Minimize the Stress Concentration for ElectroThermal Microactuator 
年度：  2011 
類別： 
會議論文

摘要：  The stress concentration of the electrothemal microactuator is an important issue in the MEMS structure resulting from the existence of stress concentration essentially to change the performance and reduce the structural life time of MEMS devices. The research proposes an optimal process using finite element method combined with the genetic algorithm programing by Matlab as an optimization for the shape design of the microactuator. The finite element method is to use the commercial package ANSYS to process the simulation and analysis. The analysis of the microactuator, which includes the displacement optimization, the output of the force optimization, the stress distribution are analyzed, and determines the most suitable geometric variables. Here, the optimal objective function is to find the maximum displacement, output force, and minimum Von Mises stress in the optimization of the shape design. By the variables of the shapes design, it is real to prove Von Mises stress distribution in the discontinuous location of the bend beam, and increase the lifetime expectancy of the microactuator. The proposed optimal process will establish an effective automated method for computeraided design process, which is a good development for the MEMS development. 
關鍵字：  MEMS, Microactuator, Stress concentration, Optimal design, Genetic algorithm 
著作名稱：  J.C. Li, David. T.W. Lin, C.C. Wang and C.Y. Yang 2010, An analysis of inverse heat conduction problem on irregular shape fins, The 2010 IAENG International Conference on Industrial Engineering, HongKong, Mar 1719. 
年度：  2010 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  W.C. Huang, J.C. Li, David. T.W. Lin 2010, An approach based on SCGM for the 3D shape optimization of the spherical vessel, The 2010 IAENG International Conference on Industrial Engineering, HongKong, Mar 1719. 
年度：  2010 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  M.S. Suen, David. T.W. Lin, Y.C. Hu, 2010, A numerical study of the heat transfer phenomena on ZnO pyroelectric film sensor, The 2010 IAENG International Conference on Industrial Engineering, HongKong, Mar 1719. 
年度：  2010 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  The optimal design process of the plate heat exchanger 
年度：  2010 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  An intelligent vehicular control based on the gravityshifting signals 
年度：  2010 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  The optimal design process of the plate heat exchanger 
年度：  2010 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  Using SCGM to optimize high power LED array design by combining experiment and finite element method 
年度：  2009 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  C.Y. Liu, I.P. Chu, K.C. Liu and David. T.W. Lin, 2009, The analysis of the thermal structure conjugated problem of the percutaneous laser disc decompression, 20th International Symposium on Transport Phenomena (ISTP20), Victoria, British Columbia, Canada, July 710. 
年度：  2009 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  F.M. Tsai, I.P. Chu and David. T.W. Lin, 2009, The heat transfer analysis of platefin heat sinks by high velocity impinging jet flow, The Asia Symposium on Computational Heat Transfer and Fluid Flow, Jeju, Korea, October 2023. 
年度：  2009 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  C.Y. Yang, I.P. Chu, P.J. Cheng, J.C. Hsieh, David. T.W. Lin and C.H. Cheng, 2009, The temperature optimization of high power LED array, The Asia Symposium on Computational Heat Transfer and Fluid Flow, Jeju, Korea, October 2023. 
年度：  2009 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  J.C. Li, I.P. Chu, C.C. Wang, Y.C. Hu, C.Y. Yang and David. T.W. Lin, 2009, Inverse estimation of temperature boundary on the gas tank, The Asia Symposium on Computational Heat Transfer and Fluid Flow, Jeju, Korea, October 2023. 
年度：  2009 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  David. T.W. Lin, C.Y. Yang, R.Y. Wang and Y.C. Hu, 2008, An improved molecular dynamics algorithm for the larger momentum molecular system, The 3rd Annual IEEE Int. Conference NEMS, Sanya, China, Jan. 69. (NSC952221E269025) 
年度：  2008 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  C.Y. Yang, David. T.W. Lin, and P.J. Cheng, 2008, A study of bioheat conduction problems by inverse estimation, Accepted by HEAT 2008, Fifth International Conference on Transport Phenomena In Multiphase Systems, Bialystok, Poland, June 30  July 3. 
年度：  2008 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  David. T.W. Lin, 2007, A molecular dynamics on the thermally developing flow of Alanine in nanochannel, The 2nd Annual IEEE Int. Conference NEMS, pp.131135, Bangkok, Thailand, Jan. 1619. (NSC942212E269017) 
年度：  2007 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  Y.C. Hu, C.S. Wei, C.C. Hsiao, and David. T.W. Lin, 2007, Extracting the Young’s modulus and stress gradient of thin films from the pullin voltage of a micro curled cantilever beam, The 2nd Annual IEEE Int. Conference NEMS, pp.278281, Bangkok, Thailand, Jan. 1619. (NSC952221E211008MY2) 
年度：  2007 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  David. T.W. Lin, W.M. Yan and H.Y. Li, 2007, The estimation of the strength of the heat source in the unsteady conjugated forced convection problem, The Asia Symposium on Computational Heat Transfer and Fluid Flow, Xi’an, China, October 1721. 
年度：  2007 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  K.C. Liu and David. T.W. Lin, 2007, Thermal response in a perfused tissue with spatial heating, The Asia Symposium on Computational Heat Transfer and Fluid Flow, Xi’an, China, October 1721. 
年度：  2007 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  David. T.W. Lin and Y.C. Hu, 2006, A molecular dynamics study of thermal ablation, The 1st IEEE Int. Conference NEMS, pp.596600, Zhuhai, China, January 1821. (NSC942212E269017) 
年度：  2006 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  Y.C. Hu, David. T.W. Lin and G.D. Lee, 2006, A closed form solution for the pullin voltage of the micro bridge with initial stress subjected to electrostatic loads, The 1st IEEE Int. Conference NEMS, pp.759763, Zhuhai, China, January 1821. (NSC942212E211006) 
年度：  2006 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  David. T.W. Lin and C.Y. Yang, 2006, Inverse estimation of twodimensional boundary conditions in bioheat conduction problems, 17th International Symposium on Transport Phenomena (ISTP17), Toyama, Japan, September 48. 
年度：  2006 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  David. T.W. Lin and C.K. Chen, 2003, Molecular plane Poiseuille flow for the TIP4P and LennardJones potentials, 6th ASMEJSME Thermal Engineering Joint Conference, Hawaii, U.S.A., March.1620. (NSC902212E006119) 
年度：  2003 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  W.M. Yan, H.Y. Li, and David. T.W. Lin, 1999, Radiation effects on mixed convection heat transfer in a square duct rotating about a parallel axis, 1999 National Heat Transfer Conference, Albuquerque, New Mexico, U.S.A., Aug.1517. 
年度：  1999 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  David. T.W. Lin and W.M. Yan, 1998, Experimental study of natural convection heat transfer in heated rotating cylinders, 11th International Symposium on Transport Phenomena (ISTP11), Hsinchu, Taiwan, Nov.29 Dec.3, pp.238243. 
年度：  1998 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  W.M. Yan, H.Y. Li and David. T.W. Lin, 1997, Mixed convection heat transfer in a radially rotating square duct with radiation effects, Proceedings of the 21st National Conference on Theoretical and Applied Mechanics, Taichung, Taiwan, Dec. 2021, pp.2534. 
年度：  1997 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  The Energy Saving Technique DevelopmentThe Metal Foam Multichannel Heat Exchanger 
年度：  2021 
類別： 
會議論文

摘要：  The purpose of this study is to develop the model of the multichannel metal foam heat exchanger (Hx) based on the porous TH model. The free and porous flow model and porous heat transfer model are used. The validation is agreed with the experiment. In this study, the effects of porosity of metal foam are discussed. The heat extraction of waste heat increases as the porosity decreases. Therefore, the enhanced heat transfer is observed apparently. This study can be used to design the optimal operating conditions of waste heat recycling.
The model of the multichannel heat exchanger is shown in Figure 1. The porous heat transfer model and free and porous flow model are used. The boundary conditions of this model are assumed as the inlet air velocity Va, in of channel (22.85m/s), the inlet air temperature Ta, in is 343.15K, the inlet temperature and velocity of water Tw, in, Vw, in is set as 293.15K and 0.00004167m3/s, the upper surface and the left and right sides are as adiabatic conditions. The difference of inlet air velocity and temperature are discussed.
Figure 2 shows the heat extraction with the porosity. The heat extraction increases as the porosity decreases. This phenomena due to the increase in the Hx between the working fluid and the metal foam. Therefore, the efficiency of heat extraction also increases. These results are validated with experiment. The related results are shown in the report of MOST1083116F024001CC2. 
關鍵字：  Metal foam, TH porous Model, Multichannel Hx 
著作名稱：  The fabrication of BiFeO3 piezoelectric sensor 
年度：  2021 
類別： 
會議論文

摘要：  In this study, we investigated the influences of the annealing temperature and parameters of spin coating on the topography of the surface and the forcefeedback analysis on a flexible substrate (PI). The piezoelectric thin films of BiFeO3 on PI substrate was synthesized by a solgel method with spincoating. In the results, we found that the topography of the surface at an annealing temperature of 500℃ was better than the one at 600℃. In advance, the XRD will be obtained and proof these results. The parameters of spin coating will discuss through the SEM and XRD. 
關鍵字：  BiFeO3, piezoelectric, film 
著作名稱：  以表面聲波元件為基礎之可撓二氧化碳感測器 
年度：  2014 
類別： 
會議論文

摘要：  本研究探討利用表面聲波元件為基礎製造出一個行動可撓之薄膜二氧化碳感測器。首先運用溶膠凝膠法(SolGel Method)調製出氧化鋅(ZnO) 溶液並利用旋轉塗佈(SpinCoating)製程進行沉積氧化鋅薄膜並加上三
乙醇胺使薄膜更為強健，繼而利用直接噴墨印表技術以奈米銀製作電極，最後再將三乙醇胺以固定的量均勻地塗抹在氧化鋅薄膜最上方作為感測層，而完成此感測器之製作。本研究利用向量網路分析儀(Vector
Network Analyzer)量測二氧化碳感測器之頻率響應，結果證明有明顯的感應現象導致訊號偏移。此二氧化碳感測器具有輕薄可攜及可撓之特點，未來將改進製程參數以強化頻率偏移量使增強感測效果。 
關鍵字：  二氧化碳感測器、氧化鋅薄膜、溶 膠凝膠法 
著作名稱：  以Brinkman模型探討超臨界二氧化碳於增強型地熱系統儲集層之熱傳現象 
年度：  2014 
類別： 
會議論文

摘要：  本文是探討超臨界二氧化碳於增強型地熱系統儲集層之熱傳現象，結合暫態熱傳模型與Brinkman模型並透過有限元素法以估算多孔介質中的流動和熱傳特性，並對儲集層中不同的壓力及入口體積流率進行討論。結果顯示不同的入口體積流率導致在出口壁面和工作流體的溫度差明顯不同，可以預見的是隨著體積流率下降，取熱量會增加。此外，因為超臨界二氧化碳的特性，將會在適當的操作壓力下達到最大取熱值。 
關鍵字：  
著作名稱：  應用板式鋁丙酮熱管之高功率LED散熱模組研究 
年度：  2014 
類別： 
會議論文

摘要：  尋求各種冷卻模組之設計，以紓緩高功率LED過熱問題，為目前研發上亟為重要之課題。本文將探討一種自行開發之板式鋁丙酮熱管為冷卻模組之被動式高功率LED冷卻模組之移熱效率，板式鋁丙酮熱管在其穩定及適於中溫操作之機制具有極佳之發展潛力。本文對比同樣LED陣列在無冷卻模組與應用板式鋁丙酮熱管之高功率LED冷卻模組的工作狀態，並對其進行模擬計算，並探討其於高功率LED上之工作效率以進行實際之運作。首先將LED佈置於銅基板，利用熱電偶測量LED接點溫度得出無散熱模組時之溫度分布，然後利用板式鋁丙酮熱管建立冷卻模組，將LED熱源以同樣的模式置於其表面，再次測量溫度分布。以此建立不同功率下LED陣列在有無散熱模組的接點溫度狀況，對比其結果計算熱移除量。繼而利用多重物理量模擬軟體，建立相應的理論模型進行熱傳分析，將實驗數據與模擬結果進行比較以相互驗證並掌握誤差，利用模擬與實驗相結合來得出鋁丙酮熱管在高功率LED散熱模組中的熱移除能力。未來將利用模擬結果進行該冷卻模組之最佳化設計。本文所提之設計將可有效於高功率電子元件進行散熱，亦可有效且廣泛應用於系統之節能設計上。 
關鍵字：  高功率LED冷卻模組鋁丙酮熱管 
著作名稱：  The Fabrication of Flexible Double Cell Split Ring Resonator based on Fully Ink Jet Printing Technology 
年度：  2014 
類別： 
會議論文

摘要：  —This study designs and fabricates an double cell split ring resonator with the properties of metamaterials by the fully inkjet printing technology and COMSOL package. The pattern made of nano silver is printed on the flexible polyimide (PI) substrate. Sparameters of this resonator are obtained from the vector network analyzer. The frequency band of the split ring resonator responses in 5.56 GHz. It can be converted to obtain the permittivity and magnetic permeability. The fully inkjet printing technology proposed in this study is robust and cheaper than the MEMS process. Through this fabricated process, the fabrication of metamaterials will become robust and faster. In addition, we expect that this fabricated method can be expanded to the most of manufactured process of film devices, such as SAW
devices, transparency film, and metamaterials. 
關鍵字：  Metamaterials; double cell splitring resonator ; Sparameter 
著作名稱：  The Effect of Graphene Growth on Impurities Catalyst Substrates 
年度：  2014 
類別： 
會議論文

摘要：  The study investigates the graphene growth on four types of industrial copper ribbons. The graphene is synthesized by low pressure chemical vapor deposition. Both of the Argon and (CH4/H2) mixture are the precursors for deposition time. The surface morphology and grain growth behavior of these films are studied by SEM and OM observation. Impurities on the Cu substrate behave as the nucleation sites in the formation of carbon cluster on Cu surface. The graphene morphologies on these 4 types
substrates are constituted by carbon discs in the range of 1~20 μm. Fractal geometry has been observed to study a variety of irregular films within a jigsaw of the variance grain structures. Current results verify the effect of surface impurities on the resulting graphene thin film. We suggest that a higher Cu purity substrate
supports formation of larger graphene grain size. 
關鍵字：  graphene, LPCVD, surface impurities 
著作名稱：  The Heat Exchanger of Heat Pipe Study for Ground Source Heat Pump 
年度：  2013 
類別： 
會議論文

摘要：  Nowadays, reducing the greenhouse gas emissions have become the common objective for countries around the world. This study presents an innovative heat exchanger of heat pipe for cooling system. By using the heat pipe for cooling air is the fundamental idea of this heat exchanger. The heat exchanger consists a heating blower to blow out hot air, a circulating cool water device, and a set of heat pipes. The results show that the temperature of air decreases apparently through the heat exchange. In addition the effects of the air velocity are discussed for the efficiency of this heat exchanger. The efficiency is better as the air velocity increases. Therefore, this innovative heat pipe exchanger is proofed through our experiment. This heat pipe Hx is suitable for the application of enhanced geothermal system (EGS). 
關鍵字：  Heat pipe, Heat exchanger, Efficiency, EGS 
著作名稱：  Mechanical response of hydrogenfilled singlewalled carbon nanotubes under torsion 
年度：  2013 
類別： 
會議論文

摘要：  Molecular dynamics simulations are performed to investigate the torsional buckling behavior of singlewalled carbon nanotubes (SWCNTs) filled with hydrogen gas. The simulation model accounts for both the mechanical deformation of the SWCNT and the interactions among the hydrogen and carbon atoms. It is found that the critical torsional moment and stiffness of the SWCNT are both significantly dependent on the hydrogen molecule storage density. Importantly, the change in torsional stiffness differs from that of conventional linear elastic materials as a result of the nonlinear oscillatory response due to nonlinear mechanical effects.It is shown that under large deformations, the SWCNT switches reversibly between different morphological patterns. Each change in pattern corresponds to an abrupt release of the strain energy and a singularity in the stressstrain curve. It is shown that at higher hydrogen storage densities, the hydrogen molecules exert a stabilizing effect on the SWCNT. The degree of torsional stability is determined principally by the distribution of the hydrogen molecules within the SWCNT. Finally, it is shown that the torsional deformation of the SWCNT is characterized by a stickslip phenomenon. 
關鍵字：  
著作名稱：  三乙醇胺於氧化鋅薄膜結晶改良之研究 
年度：  2013 
類別： 
會議論文

摘要：  本研究探討加入三乙醇胺對醋酸鋅的水解之結晶影響，運用溶膠凝膠法(SolGel Method)調配氧化鋅(ZnO)溶液過程中加入三乙醇胺(Triethylamine；TEA)，並透過旋轉塗佈(Spin Coating)沉積氧化鋅薄膜，最後以X 光繞射儀(XRD)及掃描式電子顯微鏡(SEM)來觀察其薄膜的結晶晶相、材料性質及表面形態，藉此探討加入三乙醇胺對氧化鋅薄膜表面均勻與結晶之影響性，結果驗證了醋酸鋅的水解可影響薄膜表面均勻度與結晶性，此研究可製作出具高(002)方向的氧化鋅薄膜，未來可用於增強表面聲波元件之壓電性能。 
關鍵字：  氧化鋅薄膜、三乙醇胺、溶膠凝膠法 
著作名稱：  二氧化碳於微型儲集層之熱流分析 
年度：  2013 
類別： 
會議論文

摘要：  利用地熱能源來替代化石燃料同時減少溫室效應所造成的問題為新一代的趨勢，而增強型地熱系統就是其中一個方法。因增強型地熱系統之工作流體主要為水，其受限於水資源豐富的地層，又因水的物理性質須要更多泵功導致取熱效益降低。本研究實驗方法是建立實驗室取熱系統，利用超臨界二氧化碳取代水為工作流體並注入空心測試段內探討不同壓力、流量以及溫度下超臨界二氧化碳之取熱效益，並與具有多孔介質之測試段比較取熱效益。由實驗結果可以看出流量增加會造成Nu和熱交換量提高，壓力在1500Psi時的Nu與熱交換量最大;在溫度150℃時Nu較大，但熱交換量小於200℃，這是因為二氧化碳的比熱隨著溫度改變的緣故，最後孔隙率對於Nu與熱交換量的影響不大。 
關鍵字：  超臨界流體、EGS、二氧化碳 
著作名稱：  NaAlH4金屬氫化物之卡匣式儲氫罐之熱傳分析與設計 
年度：  2013 
類別： 
會議論文

摘要：  本研究利用NaAlH4吸放氫化學反應動力方程式建立一個鋁系金屬儲氫材料之卡匣式儲氫罐。透過固態熱傳理論與金屬粉體等效熱傳導係數的物理模型的分析，完成鋁系金屬儲氫材料在不同溫度與壓力下，儲氫系統之氫氣吸附的動力曲線。在了解鋁系金屬儲氫材料吸放氫特性與反應熱的關係、材料氫化的動力特性與系統充氫的時間(refueling time)，定義出屬於應用端需求的氫化物總量、系統吸氫與放氫的最佳壓力及溫度條件。最後針對氫氣應用端需求的氫氣流率回饋相關數據，進行儲氫罐導熱能力的基本設計。 
關鍵字：  金屬氫化物、儲氫罐設計、熱傳分析 
著作名稱：  超臨界二氧化碳於多孔介質中取熱之模擬 
年度：  2013 
類別： 
會議論文

摘要：  為了瞭解超臨界二氧化碳在高溫高壓儲集層內熱傳遞及取熱之性能。本研究採用有限元素模擬軟體進行小型超臨界二氧化碳取熱模型之建立，其中藕和達西定律及熱傳模組模擬超臨界二氧化碳在多孔隙介質中流動與取熱之情形，並假設多孔介質為等向性及均質，流體在多孔介質內為飽和狀態。本文針對不同入口流速及不同的多孔介質孔隙率進行比較，結果發現入口流速增加出口溫度降低，而在入口流速較大時孔隙率的影響就越大。 
關鍵字：  超臨界流體、多孔介質、二氧化碳 
著作名稱：  壓電型熱管發電機之流場研究 
年度：  2012 
類別： 
會議論文

摘要：  近年來能源問題日益嚴重，如何尋找新的能源或能夠回收或獵取浪費之能源為許多研究者著重之課題。本研究為本年度國科會計畫「新型壓電熱管發電機之設計與製造」之研究成果，其目的為利用熱管中本已存在之蒸汽動能做為振動致電之能量來源。而其中之流場現象及熱傳沸騰現象更是熱管在不同工作溫度下所能產生電量之關鍵參數。熱管中液汽相轉換時，蒸汽通過熱管中設計之噴嘴以提高汽體流速以驅動壓電薄片振動而發電。本研究之目的為探討如何設計利用熱管內流體之流動為壓電型熱管發電機之動力來源，並探討其效率以進行實際運作。本研究於熱管中設計合適之噴嘴以提高汽體流速以驅動壓電薄片振動而達成發電之目的。研究中以實驗來探討其關係，將進行蒸汽驅動壓電片發電之實驗，以獲得熱管加熱功率及發電量間之關係。此結果可有效運用於壓電型熱管發電機之設計與製造上。 
關鍵字：  熱管發電機、壓電、振動致電 
著作名稱：  A Solution Processed ZnO Thin Film 
年度：  2012 
類別： 
會議論文

摘要：  The effect of ZincOxide (ZnO) thin film annealed in different ambiences is presented. To achieve low cost and environmentally friendly process, ZnO aqueous solution is synthesized by dissolving zinc acetate dihydrate in deionized water directly. Zinc oxide aqueous solution of high solubility and stability is presented. High quality and dense Zinc oxide thin film is formed by spin coating. Annealing temperatures are in the range of 300 °C~500 °C, and annealing ambiences of both air and N2 are discussed. 
關鍵字：  Thin Film Transistor, Thin Film Property, ZnO, Solution Process 
著作名稱：  CMOS製程相容之樑結構應力模擬分析技術 
年度：  2012 
類別： 
會議論文

摘要：  This research provides a technique to predict the elastic deformation of a CMOSMEMS bridge structure subjected to the mean stress and gradient stress. First, the stress boundaries are setting to obtain the equivalent mechanical model. And then using the commercial software ANSYS to simulate the deformation of a beam under stress conditions. The simulation results about the predeformation caused by residual stress agree well with experimental data. Therefore, an analytical method of a CMOSMEMS bridge with residual stress is developed in this paper, which can be used to improve the reliability of the CMOSMEMS structure. 
關鍵字：  CMOSMEMS bridge structure, mean stress, gradient stress 
著作名稱：  氧化鋅薄膜性質在可撓表面聲波元件上之研究 
年度：  2012 
類別： 
會議論文

摘要：  近幾年來感測器蓬勃發展，表面聲波感測器已成為關注重點，由於表面聲波元件裝置有極少數被製造於可撓式基板，其將可促使表面聲波元件裝置應用更加多元化。本文研究可撓式表面聲波元件之氧化鋅薄膜性質，運用溶膠凝膠法(SolGel Method)調配氧化鋅(ZnO)溶液，並透過旋轉塗佈(Spin Coating)沉積氧化鋅薄膜，最後以X 光繞射儀(XRD)及掃描式電子顯微鏡(SEM)來觀察其薄膜的結晶晶相、材料性質及表面形態，藉此探討旋轉塗佈轉速對氧化鋅薄膜結晶之影響性，在未來利用結晶性良好之氧化鋅薄膜製造可撓式表面聲波元件。 
關鍵字：  表面聲波感測器、氧化鋅薄膜、壓電材料、溶膠凝膠法 
著作名稱：  運用基因演算法於微流道散熱器之通道內連結之最佳化設計 
年度：  2012 
類別： 
會議論文

摘要：  近年來，隨著半導體技術蓬勃發展與成熟，電子產品不斷趨向小體積、高效能及高功率發展，並擴展應用至消費型電子和醫療系統等領域，因此微流道散熱器之使用也越來越普遍。本研究整合有限元素分析軟體與最佳化方法來進行微流道散熱器之最佳化設計，其使用之最佳化方法為基因演算法(Genetic Algorithm)，有限元素方法則是運用商業套裝軟體COMSOL Multiphysics 來進行模擬及分析。本研究針對微流道散熱器之三維模型取兩通道之中連結長度、壓力分佈及溫度分佈進行探討，以最適合之幾何參數與散熱器之散熱效率為最佳化目標函數來進行最佳化設計。分析結果顯示，藉由改變不同連結長度幾何參數，可以找到有效設計之目標，並提高散熱性能。 
關鍵字：  微流道散熱器、最佳化設計、基因演算法 
著作名稱：  Optimization of the Micro Channel Heat Sink by Combing Genetic Algorithm with Finite Element Method 
年度：  2012 
類別： 
會議論文

摘要：  This paper presents an optimization design of micro channel heat sink. The three dimensional model of this heat sink with fluid flow cooling is investigated by numerical simulations. The optimization algorithm in this paper combines finite element method with genetic algorithm. The objective of this optimization design is improving the ability of heat dissipation for the micro channel heat sink. The design variables of this optimization design include the number of channel N, channel aspect ratio α and the ratio of channel width to pitch β. Moreover, this paper even considers the weight of this micro channel heat sink in the optimal design process. The results show that the heat dissipative ability can be improved, and the weight of this micro channel heat sink can be decreased, individually or simultaneously. 
關鍵字：  
著作名稱：  新型主動式微型薄膜致冷器之熱傳分析 
年度：  2011 
類別： 
會議論文

摘要：  高功率電子元件損毀的原因通常是過度熱集中所導致，因熱無法有效快速地傳遞至散熱端，使元件之溫度不斷上升，造成元件故障。本研究主要目的是發展一主動式微型致冷器以應用於高功率LED或高單位面積熱集中元件之熱移除，利用致冷器內薄膜震動所導致之強制對流循環方式，將元件之熱量以熱擴散之方式快速移出，以達到快速移熱之效果。本研究將使用有限元素法商業軟體COMSOL，利用流固耦合模組和熱傳模組，並搭配移動網格技術，模擬此主動式微型致冷器應用於高單位面積熱集中元件時之熱傳現象。研究結果顯示，所提出之方法可以趨緩元件溫度之上升時間，達到熱量快速移除之效果。有效利用此主動式微型致冷器將能提升元件之效率、穩定性及使用壽命。本研究所提出方法適用於各式高功率元電子元件冷卻之設計，能有效將熱快速擴散，降低二次散熱元件之耗能。 
關鍵字：  高功率電子元件、微型致冷器、熱擴散、有限元素法 
著作名稱：  Design and optimization of the LED lamp holder 
年度：  2010 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  Optimal design of composite pressure vessel by using the genetic algorithm 
年度：  2010 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  Optimal residual stress in CMOS fabrication 
年度：  2010 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  W.C. Huang, I.P. Chu, C.H. Cheng, David T.W. Lin，2009，Optimization of the shape design for pressure vessels，中國機械工程學會第二十六屆全國學術研討會，台南，台灣，十一月。 
年度：  2009 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  C.Y. Liu, C.H. Cheng, Y.C. Hu, David T.W. Lin，2009，Optimal design of the shell and tube heat exchanger，中國機械工程學會第二十六屆全國學術研討會，台南，台灣，十一月。 
年度：  2009 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  M.J. Kuo, P.J. Cheng, C.Y. Yang, C.H. Cheng, and David T.W. Lin, 2009, The minimum of thermal resistance design of high power LED package, The 1st International Conference on Mechatronic System of Integration and Application 2009 (ICMS09), Tainan, Taiwan, Dec 45. 
年度：  2009 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  J.C. Li, C.C. Wang, C.Y Yang and David T.W. Lin, 2009, An analysis of the high pressure gas tank with inverse method, The 1st International Conference on Mechatronic System of Integration and Application 2009 (ICMS09), Tainan, Taiwan, Dec 45. 
年度：  2009 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  C.Y. Liu, C.H. Cheng, Y.C. Hu and David T.W. Lin, 2009, The optimum model approach of the shellandtube heat exchanger, The 1st International Conference on Mechatronic System of Integration and Application 2009 (ICMS09), Tainan, Taiwan, Dec 45. 
年度：  2009 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  C.Y. Yang, K.C. Liu, J.C. Hsieh, David T.W. Lin and C.H. Cheng, 2009, LED location design of high power LED array to the temperature optimization, The 1st International Conference on Mechatronic System of Integration and Application 2009 (ICMS09), Tainan, Taiwan, Dec 45. 
年度：  2009 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  F.M. Tsai, I.P. Chu, H.Y. Li., Y.C. Hu and David T.W. Lin, 2009, A numerical study of jet cooling effect on the pin fin heat sinks, The 1st International Conference on Mechatronic System of Integration and Application 2009 (ICMS09), Tainan, Taiwan, Dec 45. 
年度：  2009 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  W.C. Huang, I.P. Chu, J.C. Li, David T.W. Lin and C.H. Cheng, 2009, Shape design of the pressure vessels under the working pressure based on an optimal approach, The 1st International Conference on Mechatronic System of Integration and Application 2009 (ICMS09), Tainan, Taiwan, Dec 45. 
年度：  2009 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  H.J. Huang, S.C. Shen, David T.W. Lin and J.C. Hsieh 2009, Experimental study of high power LED array on flat plate heat pipe, The 1st International Conference on Mechatronic System of Integration and Application 2009 (ICMS09), Tainan, Taiwan, Dec 45. 
年度：  2009 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  David. T.W. Lin, and M.S. Suen, 2009, The heat transfer analysis of the protein flow on the micro channel by parallel molecular dynamics study and new molecular list algorithm, The 1st International Conference on Mechatronic System of Integration and Application 2009 (ICMS09), Tainan, Taiwan, Dec 45. 
年度：  2009 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  朱弋鵬，徐銘鴻，林大偉，陳翊航，蔡芳明，2008，於高速衝擊噴流下電子元件冷卻之熱傳分析，中國機械工程學會第二十五屆全國學術研討會，彰化，台灣，十一月。 
年度：  2008 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  朱弋鵬，陳翊航，林大偉，徐銘鴻，劉正堯，2008，經皮雷射椎間盤減壓術之暫態熱傳分析，2008年生物醫學工程年會暨科技研討會，林口，台灣，十二月。 
年度：  2008 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  王瑞詠，楊慶煜，林大偉，2007，分子動力學模擬之新分子表列法則，中國機械工程學會第二十四屆全國學術研討會，中壢，台灣，十一月。(NSC952221E269025) 
年度：  2007 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  P.J. Cheng, K.C., Liu, and David. T.W. Lin, 2007, “Nonlinear hydromagnetic longwave instability of a viscoelastic liquid layer flowing down a vertical cylinder,” The 31st National Conference on Theoretical and Applied Mechanics, Kaohsiung, pp. B05_18. (NSC 952221E269027). 
年度：  2007 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  林大偉，王彥杰，朱柏翰，徐銘鴻，黃朝偉，陳翌航，2006，蛋白質流體於具熱邊界奈米流道之流場研究，中國機械工程學會第二十三屆全國學術研討會，台南，台灣，十一月。(NSC942212E269017) 
年度：  2006 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  David. T.W. Lin, C.Y. Yang, P.J. Cheng, and K.C. Liu, 2006, An inverse study of boundary conditions in bioheat conduction problems, 科技與管理學術研討會，台南，台灣，十二月。 
年度：  2006 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  林大偉，陳朝光，2004，奈米殼層之放熱過程於蛋白質中之熱傳分析. 中國機械工程學會第二十一屆全國學術研討會，高雄，台灣，十一月。 
年度：  2004 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  林大偉，陳朝光，2001，TIP4P分子勢能於平板完全發展流上之研究，中國機械工程學會第十八屆全國學術研討會，台北，台灣，十二月。 
年度：  2001 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  林大偉，陳朝光，2000，分子動力學於空穴流上之研究，中國機械工程學會第十七屆全國學術研討會，高雄，台灣，十二月。 
年度：  2000 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  林大偉，顏維謀，1998，旋轉對傾斜加熱圓柱體內自然對流熱流之影響.中國機械工程學會第十五屆全國學術研討會，台南，台灣，十一月，pp.371378。 
年度：  1998 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  於實驗室尺度建置實驗系統及模擬探討CO2EGS於儲集層之熱流現象 
年度：  2013 
類別： 
會議論文

摘要：  
關鍵字：  
著作名稱：  林大偉，2009，以平行分子動力學結合新表列法則於三維流道內蛋白質流體之熱流性質分析，98年度台南大學校內計畫結案報告。 
年度：  2009 
類別： 
研究計畫成果報告

摘要：  
關鍵字：  
著作名稱：  林大偉，2008，直接甲醇燃料電池於甲醇穿透率之動態模擬與實驗，國科會報告NSC962221E269007。 
年度：  2008 
類別： 
研究計畫成果報告

摘要：  
關鍵字：  
著作名稱：  林大偉，2008，霧化型均熱板之評估分析，工研院計畫結案報告。 
年度：  2008 
類別： 
研究計畫成果報告

摘要：  
關鍵字：  
著作名稱：  林大偉，2007，鋁製板式熱管之逆運算分析，工研院計畫結案報告。 
年度：  2007 
類別： 
研究計畫成果報告

摘要：  
關鍵字：  
著作名稱：  林大偉，2007，分子動力學於直接甲醇燃料電池之甲醇穿透率模擬，國科會報告NSC952221E269025。 
年度：  2007 
類別： 
研究計畫成果報告

摘要：  
關鍵字：  
著作名稱：  林大偉，2007，藻類特用化學品試量產技術研發計畫養殖槽熱傳分析，人宇生物科技股份有限公司政府補助計畫案。 
年度：  2007 
類別： 
研究計畫成果報告

摘要：  
關鍵字：  
著作名稱：  林大偉，2006，奈米殼層之放熱過程於氨基酸中之熱傳分析，國科會報告NSC952212E269017。 
年度：  2006 
類別： 
研究計畫成果報告

摘要：  
關鍵字：  
著作名稱：  林大偉，湯同達，李弘毅，2003，分子動力學，教育部大學生跨領域科技能力培養研究計畫微/奈米光機電跨領域研究計畫授課講義，92年。 
年度：  2003 
類別： 
研究計畫成果報告

摘要：  
關鍵字：  
著作名稱：  陳朝光，林大偉，2002，分子動力學於微容器內自然對流熱傳現象之研究，國科會報告NSC902212E006119。 
年度：  2002 
類別： 
研究計畫成果報告

摘要：  
關鍵字：  
著作名稱：  林大偉，李弘毅，陳冠穎，2002，奈米工程導論，教育部大學生跨領域科技能力培養研究計畫微/奈米光機電跨領域研究計畫授課講義。 
年度：  2002 
類別： 
研究計畫成果報告

摘要：  
關鍵字：  
著作名稱：  顏維謀，林大偉，1998，單晶之VCD薄膜和熔化成長法製程的不穩定熱流與使其穩定之研究(Ⅲ)之子計畫五：垂直Bridgman單晶熔化成長法製程中的流體運動及熱傳之實驗研究(Ⅲ)，國科會報告NSC872212E211006。 
年度：  1998 
類別： 
研究計畫成果報告

摘要：  
關鍵字：  
著作名稱：  顏維謀，林大偉，1997，單晶之VCD薄膜和熔化成長法製程的不穩定熱流與使其穩定之研究(Ⅱ)之子計畫五：垂直Bridgman單晶熔化成長法製程中的流體運動及熱傳之實驗研究(Ⅱ)，國科會報告NSC852212E211005。 
年度：  1997 
類別： 
研究計畫成果報告

摘要：  
關鍵字：  