國立臺南大學教師基本資料

基本資料
姓名 白富升
系所 電機工程學系
職稱 教授
校內分機 170
傳真
辦公室/研究室 榮譽校區 C301
E-mail fspai@mail.nutn.edu.tw
網址
專長/研究領域 電力、能源管理系統、綠色能源
 

畢業學校國別主修學門學位修業期間
國立成功大學電機工程博士1998/8~2002/6

服務機關部門 / 系所職稱服務期間
台達電子工業股份有限公司不斷電系統工程資深工程師2000/7~2002/1
崑山科技大學電機工程系助理教授2002/8~2005/7
國立臺南大學環境與能源學系助理教授2005/8~2007/2
國立臺南大學環境與能源學系副教授2007/2~2008/1
國立臺南大學電子工程學系副教授2008/2~迄今

著作
名稱S. J. Huang and F. S. Pai, “A New Approach to Islanding Detection of Dispersed Generators with Self-Commutated Static Power Converters,” IEEE Transactions on Power Delivery, Vol. 15, No. 2, April 2000, pp. 500-507. (SCI)
年度2000
類別期刊論文
摘要 
關鍵字 
名稱S. J. Huang and F. S. Pai, “Design and Operation of Grid-Connected Photovoltaic System with Power-Factor Control and Active Islanding Detection,” IEE Proceedings of Generation, Transmission and Distribution, Vol. 148, No. 2, March 2001, pp. 243-250. (SCI)
年度2001
類別期刊論文
摘要 
關鍵字 
名稱F. S. Pai and S. J. Huang, “A Detection Algorithm for Islanding-Prevention of Dispersed Consumer-Owned Storage and Generating Units,” IEEE Transactions on Energy Conversion, Vol. 16, No. 4, December 2001, pp. 346-351. (SCI)
年度2001
類別期刊論文
摘要 
關鍵字 
名稱S. J. Huang and F. S. Pai, “Design and Operation of Burn-In Test System for Three-Phase Uninterruptible Power Supplies,” IEEE Transactions on Industrial Electronics, Vol. 49, No. 1, February 2002, pp. 256-263. (SCI)
年度2002
類別期刊論文
摘要 
關鍵字 
名稱C. J. Huang, S. J. Huang, and F. S. Pai,“Design of Dynamic Voltage Restorer with Disturbance-Filtering Enhancement,” IEEE Transactions on Power Electronics, Vol. 18, No. 5, September, 2003, pp. 1202-1210. (SCI)
年度2003
類別期刊論文
摘要 
關鍵字 
名稱F. S. Pai, “An Improved Utility Interface for Micro-turbine Generation System with Stand-alone Operation Capabilities,” IEEE Transactions on Industrial Electronics, Vol. 53, No.5, October 2006, pp. 1529-1537. (SCI)
年度2006
類別期刊論文
摘要 
關鍵字 
名稱F. S. Pai and S. J. Huang, “A Novel Design of Line-interactive Uninterruptible Power Supplies without Load Current Sensors,” IEEE Transactions on Power Electronics, Vol. 21, No. 1, January, 2006, pp. 202- 210. (SCI)
年度2006
類別期刊論文
摘要 
關鍵字 
名稱F. S. Pai and S. J. Huang “Design and Operation of Power Converter for Micro-Turbine Powered Distributed Generator with the Capacity Extension Capability,” IEEE Transactions on Energy Conversion, Vol. 23, No. 1, March 2008, pp.110-118. (SCI)
年度2008
類別期刊論文
摘要 
關鍵字 
名稱Design of an Inverter Array for Distributed Generations with Flexible Capacity Operations
年度2010
類別期刊論文
摘要In this paper, an inverter array structure for the distributed generation is proposed. In the method, the inverter array is organized by basic and extended units, in which basic units are grouped to evenly share the capacity of primary energy source while extended units are designated for on-line redundant services. Through this design, it is not only beneficial to improve the reliability of energy production, but also owns high flexibility of capability extension. To validate the effectiveness of this method, both simulations and hardware realizations have been made and evaluated. Test results help support the proposed approach for grid-connected operations.
關鍵字distributed generation, alternative energy source, inverter, reliability, parallel operation, current control, PWM controller, load sharing control.
名稱Performance Evaluation of Parabolic Prediction to Maximum Power Point Tracking for PV Array
年度2011
類別期刊論文
摘要In this paper, a tracking method based on parabolic function is proposed to perform the photovoltaic maximum power point tracking (MPPT). With the proposed method, the maximum power calculation is made from a parabolic convex function. Then a systematic scheme is developed to adjust the concavity and optimal region of the approximate parabola for ensuring the iterative convergence of the proposed method. In order to confirm the effectiveness of this proposed design, the approach has been applied to investigate different atmospheric scenarios. Performance comparison with the conventional method is also made for the assessment of different scenarios considered. Test results consolidate the feasibility of the approach for the applications considered.
關鍵字photovoltaic generating system, maximum power point tracking, parabolic function
名稱Plasma-Driven System Circuit Design with Asymmetrical Pulse Width Modulation Scheme
年度2011
類別期刊論文
摘要In this paper, the circuit design of resonant inverter for plasma-driven system is studied. Based on the half-bridge inverter structure, the proposed circuit has included the soft-switching techniques so that the investment on heat dissipation can be greatly saved. Moreover, the paper has investigated the plasma power control under different conditions. Via the developed control circuit to formulate the relationships between the output power and voltage as a quadratic function, the output power of system can be then controlled and becomes insensitive to plasma voltage variations. In order to solidify the practicality of this circuit design, mathematical analyses and experimental validations have been thoroughly performed. Test results help confirm the effectiveness of the method, demonstrating its feasibility and practicality for high-frequency drive industry applications.
關鍵字plasma power, half-bridge inverter, hybrid resonant, power control, asymmetrical pulse width modulation
名稱Novel Design of a Modular Dynamic Voltage
年度2011
類別期刊論文
摘要In this paper, based on the paradigm of the cascade inverter technique, a new approach to control the dynamic voltage restorer will be proposed. In the method, the required series voltage for the sag correction is first decoupled by the vertical and horizontal component referred to the phase of load current. The vertical and horizontal voltage component is then generated and compensated via the different reactive and active power module. In this case, as the super capacitor-aided reactive power module can output a large amount of the compensation power, the proposed system will take full advantages of less real power injection during the DVR operation, mitigating a severe and long duration voltage sag with a significantly smaller energy demand from the cascaded inverter. The method proposed in this paper will be examined under various scenarios. The results help consolidate the feasibility and practicability of the approach for the applications considered.
關鍵字Power Quality, Dynamic voltage restorer, Inverter
名稱An Approach to Measurements of Electrical Characteristics of Lithium-ion Battery with OCV Function
年度2013
類別期刊論文
摘要Comprehension of open-circuitvoltage (OCV) function and battery impedance can be used to evaluate the residual energy and dynamic voltage response of lithium batteries. However, noise contamination during data sampling may affect the accuracy of the derived OCV function and battery impedance extraction, resulting in a poor evaluation performance. By aiming at formulating a more representative circuit-based model, this study proposes a hybrid averaging method along with an impedance network observation approach that is embedded within a time–frequency localisation method, anticipating eliminating the influences of sampling noise such that the characterisation of the OCV function and battery impedances can be better ensured. In such an integrated approach, the trimmed relevance vector regression is also added, which is followed by two cascaded R–C networks in order to fit the characteristics of battery impedances. Through the method proposed in this paper, it is found that the average error can be decreased to be less than 20 mV. Both battery residual energy and I–V performance are more effectively comprehended.
關鍵字
名稱馬達發電機組電能轉換電路
年度2013
類別期刊論文
摘要本文主要在於研究一套適用於一體式起動馬達發電機之雙向電能轉換電路。此系統在馬達啟動時經由三相換流器驅動,使得引擎得以加速。另當引擎到達一定轉速後,電路即切換至發電機模式,此時經由換流器內之背接二極體及降壓型轉換器作用後,即可將發電機產生之電能轉換成直流格式儲存於電池中。在電路設計方面,本文採用超電容強化馬達啟動瞬間性能,並使用微處理器完成數位控制,故可大幅增加所提驅動電路之穩定性。本文已針對轉換電路之馬達及發電機操作模式進行理論分析,並經由模擬軟體與實際系統測試,驗證馬達系統驅動與電能轉換功能。由實驗結果可證實本文之可行性,相關研究心得及數據可供電力人員參考及利用。
關鍵字電能轉換器、發電機
名稱Circuit Design of Signal Sensing and Transmission for Strain Gauge Using Zigbee Network
年度2014
類別期刊論文
摘要本文旨在建立應用於塑膠射出成型機之應變規訊號感測電路,並使用Zigbee 無線網路融入數據傳輸與遠方監測控制功能。本文所提系統首先藉由應變規、儀表放大器、微控制器取樣及類比數位轉換,接著將轉換之電阻訊號經由Zigbee 無線網路之端節點模組回傳至協調器模組,再利用電腦程式顯示目前感測資訊,進而將其數據儲存,故其不僅可提供後續分析之需,同時可俾以掌握塑膠射出成型機之動作狀態。本文於文中已完成感測電路設計、監控平台架設、並由實驗驗證其確能整合應變規、Zigbee 無線感測網路訊號傳遞及系統監視之效能。相關研究成果應已具學術探討及實務應用之參考價值。
關鍵字應變規
名稱a new dynamic voltage restorer with separating active and reactive
年度2015
類別期刊論文
摘要Conventional dynamic voltage restorers (DVRs) install parallel battery and capacitor sets at the DC bus to supply the required power for voltage sag compensation. However, the reactive power output of a DVR may increase the ripple voltage at the inner DC bus, possibly resulting in a higher operating temperature of the battery and thus decreased battery life. This paper proposes a DVR system that uses a cascade power module to effectively compensate voltage sag. By separating the active and reactive compensation powers, the proposed DVR provides a lower ripple DC link for extending battery life and offers a flexible way to design the capacitor bank. To confirm the effectiveness of the proposed design, theoretical analysis and experimental validation were conducted under various scenarios. Test results confirm the feasibility and practicality of the proposed method.
關鍵字voltage sag; dynamic voltage restorer; power module; power quality;
名稱Sag correction and power transfer of double feeder circuit using unified power quality conditioner
年度2016
類別期刊論文
摘要Alternative energy power generation has emerged as a crucial research topic in studies on modern energy systems. Because of the inherently intermittent generating feature of distributed generation systems, system operations associated with the integration of distributed generation into existing power networks may suffer from voltage variations and power delivery problems. Therefore, this paper proposes a new unified power quality conditioner (UPQC) scheme. The proposed UPQC consists mainly of two back-to-back inverters that are connected together by a direct current capacitor and installed in series and in parallel with two adjacent feeders. The UPQC can be operated not only for maintaining a downstream voltage to mitigate upstream voltage sags but also for absorbing real power from one feeder and transferring it to the other feeder. To validate the effectiveness of the proposed scheme, scenarios including voltage sags and power transfer between two feeders were tested through experimental validations. The test results help consolidate the feasibility and practicability of the scheme for potential applications.
關鍵字unified power quality conditioner; voltage sag; power transfer
名稱Cumulative current-magnetizing method for a capacitor-discharged impulse magnetizer
年度2017
類別期刊論文
摘要This paper presents a cumulative current-magnetizing method for magnetization of permanent magnet, aimed at alleviating the bulky capacitor problem of traditional capacitor-discharged impulse magnetizers. The method employs circuit resonance to boost the output voltage. The resonant alternative current (ac) voltage is then directly discharged to the magnetizing coil without using any rectifier. The proposed resonant ac discharge repeats a number of times over several milliseconds. This allows the magnetizing current to increase incrementally until it reaches the peak that is sufficient to fully magnetize the permanent magnet. With this design, the energy for magnetization is accumulated by small steps, and each increment would require much lower energy. This results in smaller capacitors needed compared to traditional designs. To validate the effectiveness of the proposed scheme, several pieces of ferrite magnet without being pre-magnetized were tested using the developed magnetizer. The test results support the feasibility and practicability of the scheme for potential applications.
關鍵字capacitor discharge; magnetizer; resonance; permanent magnet; magnetization
名稱An efficient GWO MPPT for a PV system using impedance information acceleration
年度2018
類別期刊論文
摘要This paper presents a novel maximum power point tracking (MPPT) method based on the grey wolf optimisation (GWO) technique for photovoltaic (PV) power generation systems. The proposed method utilises previous working duty cycles and their corresponding voltage and current data to compute the instantaneous DC impedance of a PV string. To determine the peak power characteristics of any PV string, the impedance variation of that PV string is used as an efficient shading factor. This shading factor simplifies the calculation of the GWO-MPPT algorithm to obtain multiple peak targets under partial shading conditions. Thus, the efficiency of the proposed power tracking technique can be improved considerably. The effectiveness of this method was validated through both simulation and hardware implementations. Results revealed that the search performance of five iterations of the proposed method was similar to that of ten iterations of a traditional GWO-MPPT method under normal conditions without shading. These results confirm the practicability of the proposed method in various applications.
關鍵字Photovoltaic power generation system; maximum power point; Grey Wolf Optimization; partial shading; power converter
名稱Design and Implementation of an Utility Interface for Micro-turbine Generation System
年度2019
類別期刊論文
摘要This paper is aimed at researching a modular inverter for the grid-tied micro-turbine power generation system. By coupling with the developed method, the operational reliability and loss factor are first evaluated, where the results can output to help further decide the amount of the duty inverter modules. Then, a current-sharing scheme as well as a modular arrangement is developed to expand the inverter circuit being capable of the parallel operation of multi-modular in anticipation of increasing the reliability and efficiency requirements of installed. The method proposed in this paper was examined under various scenarios. The results help consolidate the feasibility and practicability of the approach for the applications considered.
關鍵字micro turbine generator, power converter
名稱Design and realization of a Magnetizer for Ferrite Magnet
年度2019
類別期刊論文
摘要To meet the application requirements, parts of the permanent magnets are not magnetized directly after production. They have to be magnetized afterwards by application of a high external field which can come from a magnetizer. Therefore, in this paper, a method based on the inverter circuit is proposed. In the method, the inverter is first included to generate a basic square voltage. A voltage intensifier is then utilized to further boost this square voltage. This process is followed by using the designed switching capacitors and natural inductive characteristics of magnetizing coil so that the proposed method can provide large magnetizing current to loads. To validate the effectiveness of the method, a prototype is set up in the laboratory. The hardware tests with the non-magnetic ferrite magnet is made. Test results indicate that the proposed method can generate the required magnetizing current indeed.
關鍵字Magnetic material, ferrite, magnetizer.
名稱Operating Efficiency Enhancement of Hybrid Energy Storage System for IPMSM Drives
年度2020
類別期刊論文
摘要This paper proposes a control strategy to enhance the operating efficiency of a Hybrid Energy Storage System (HESS) for an Interior Permanent Magnet Synchronous Motor (IPMSM) drive. In this method, the battery and super-capacitor (SC) are connected by an interleaved DC-DC (DD) converter where a bypass DD scheme with the inherent anti-parallel diode of power switches is used to create another shorter path for battery discharge. In this design, an adjustable dc-link voltage is accomplished to fit the characterizations in various motor operating conditions. Then, with the corresponding control design, the proposed HESS can operate in an optimal state to improve efficiency and extend the battery lifetime. To validate the effectiveness of the method, several operation scenarios including acceleration, constantspeed and deceleration of the IPMSM are examined using simulations. This is further supported through the experimental study. The test results obtained under the buck, boost and bypass converter scenarios consolidate the feasibility and practicality of the proposed approach in an attempt for potential electric vehicle applications.
關鍵字energy storage system inverter motor drive electric vehicle, motor
名稱A Control Approach Integrating Electric Vehicle Charger and Dynamic Response of Demand‑Side Resource Aggregators
年度2020
類別期刊論文
摘要Regardless of whether level 1, level 2, or dc fast charging, several methods are under development or available as an aftermarket option for Plug-in electric vehicles (EVs). While confining the charging behavior of EVs to low-load periods is difficult, it leads to significant and uncertain load peaks and valleys in the utility power network. Therefore, this paper proposes a new method for an electric vehicle charger. The proposed charging method involves power supervisory characteristics on the basis of the paradigm of a constant-current and a constant-voltage (CC–CV) charger so that the external commands from the demand-side resource aggregator in the smart grid can be executed. In the method, first, a feedback loop is included in the controller to formulate the relationship between battery voltage and charging power as a quadratic concave downward polynomial. The controlled output power at the beginning of constant voltage charging is then set to the maximum value of the quadratic polynomial because the charging power requirement near this point is closed to the highest. Hence, if the charging power is lower than the allowable maximum power, the proposed charger is determined to have followed the traditional CC–CV charging steps. On contrast, the proposed circuit launches the power control loop when the actual charging power is beyond the maximum power limitation of aggregator. The proposed charger can keep the power consumption inside an allowable range of aggregator. That is the power consumption at the EV charging sites becomes directly programmable by their aggregators. The proposed method is examined by conducting an interactive test of a remote energy management system and the proposed controller. The results revealed that the proposed method provide an easy method to dynamically control consumption pattern of the EV charging for demand-side power management.
關鍵字Demand-side management, Dynamic demand response , Electric vehicle , Power management
名稱應用於微型氣渦輪機之直交流電能轉換器控制整合設計
年度2012
類別會議論文
摘要適用於微型氣渦輪機之直交流 電能轉換器的控制整合策略,本文規劃以單一的電 流迴授路徑,完成其市電併聯供電及備用發電機兩 種模式控制。本文並已在發電機的並聯供電模式 中,融入負載功因矯正及主動濾波功能,使氣渦輪 機的並聯運轉兼具負載管理概念,增加氣渦輪發電 機組之經濟運轉價值。由電腦模擬及系統測試結果 顯示,本文所提之方法確具可行性,相關研究成果 應具相當之實務應用參考價值。
關鍵字分散型發電系統、微型氣渦輪機,電能轉
名稱應用於動態電壓恢復器之電能轉換系統研究
年度2012
類別會議論文
摘要傳統型動態電壓恢復器雖已能協助解決電壓驟降之問 題,但在電力系統運轉實務上,因分散式發電系統已被允許 加入電力系統運轉,且得以逆送電力售予電力公司,因此其 出口端鄰域即有長期電壓偏高等程度不等的電力品質問題, 此時對於結合發電系統之現代電力系統而言,電壓品質的改 善實已無法再侷限於電壓驟降之範圍。基於此,本文即在研 究應用在動態電壓恢復器的電能轉換技術,其中考慮電力公 司在高品質需求的供電地區常採雙迴路饋電架構,本文提出 利用兩組換流器與兩組變壓器,輔以直流匯流排共用結構之 動態電壓恢復器技術,並使其分別連結於不同配電站之兩迴 路,因此不同饋線在組態中具隔離跨接特性。此時兩獨立饋 電回路即有實、虛功率潮流互相轉移之可行性,因此可藉由 功率之互相支援與調度達到市電高電壓調節控制之目的。
關鍵字動態電壓恢復器、分散式發電系統
名稱DC-to-AC Power Inverter and Method of Operation Thereof, US. Patent, No. 6791850, October, 2004.
年度2004
類別研究計畫成果報告
摘要 
關鍵字 
名稱Electronic Voltage Regulator with Switching Control Device and Control Method for Stabilizing Output Voltage, US. Patent, No. 677098, August, 2005
年度2004
類別研究計畫成果報告
摘要 
關鍵字 
名稱Parallel DC-to-AC Power Inverter System with Current Sharing Technique and Method Thereof, US. Patent, No. 6947300, September 2005.
年度2005
類別研究計畫成果報告
摘要 
關鍵字 
名稱電子式電源穩壓器之控制方法與裝置,中華民國專利 I244251
年度2005
類別研究計畫成果報告
摘要 
關鍵字 
名稱直流-交流電壓轉換電路及控制方法,中華民國專利 I253227
年度2006
類別研究計畫成果報告
摘要 
關鍵字 
名稱Electronic Power Source Voltage Regulator with UPS Function, US. Patent, No. 7116013, October 2006.
年度2006
類別研究計畫成果報告
摘要 
關鍵字